20 Most Recent
2012 Suzuki RM-Z 450 Questions & Answers
Add gear oil how much
If there is not a dipstick or a sight glass, the dirt bikes usually have a weep type setup. Which means there will be a screw on the cover sometimes it has a small copper washer. You fill it til the fluid just starts coming out of the hole. Then you have the correct amount. I’m happy to assist further over the phone at
https://www.6ya.com/expert/robert_5bac37c3cb991fdb
I have a 2005 RMZ
Sounds like your ratchet gear is mis aligned, when you put the ratchet gear
together it has alignment marks that have to line up when you insert it back in
the case...The kick shaft being bent slightly should not prevent the engine from turning over. I hope this helps.
Cant get them to peel
An interesting concept... Peeling Motorcycles.
Can I have a pint of what you are drinking please.
Problem is in top rev
You need to most likely have the TPS checked (set at full throttle not running 4.85 volts) and or CDI remaped at dealer
How do you drain the fuel out of a 2008 suzuki rmz 450
Remove the feed pipe to the injectors and you will be able to drain the fuel, but you will have to use the ignition to do so.
The other way would be to remove the feed pipe to the pump from the tank, this way you will be able to remove the fuel without the ignition.
Hope this helps!
Where is the rectifier located on my 2004 suzuki katana 600
Behind the radiator on the left side. It is the device with cooling fins, even though the electronic parts are embedded in rubber paste.The location isn't ideal and sudden defects leave people stranded so what people do is relocate the regulator/rectifier to a cooler place. Perhaps to the air inlet, under the air filter. Follow the three, mostly, yellow cables that originate from the stator when you don't find it behind the radiator.
3/24/2024 3:09:20 AM •
Suzuki...
•
Answered
on Mar 24, 2024
Why my Suzuki TF 125 losses power in the midway? What are the causes for such loss of power?
What do you mean by "Midway"? How old is this motorbike? What exactly did you do to clean the carburettor? Is it a new spark plug and a new, clean air filter? Did you empty the fuel tank to remove the fuel tap to clean the filter on the inside of the tap?
Is it doing anything else? Things like - is it hard to start, has heavier exhaust smoke or it has a rough and uneven idle.
2/18/2024 5:20:58 PM •
Suzuki...
•
Answered
on Feb 18, 2024
Bypass immobilizer on 2007 Suzuki R6
You can't, the computerized system is in place to stop exactly what you are trying to do, Steal the bike without the correct credentials. You can't reprogram or over-ride the computer. You need a bike electrician.
12/20/2023 3:33:40 AM •
Suzuki...
•
Answered
on Dec 20, 2023
Where is air/fuel screw on a suzuki vs 800 intruder
The air/fuel mixture screw on a Suzuki VS800 Intruder is typically located on the carburetor. To adjust the air/fuel mixture, you'll need to locate the carburetor and look for a small screw that can be turned.
Keep in mind that the exact location of the screw may vary slightly depending on the model year and specific carburetor version on your VS800 Intruder. Generally, it is located on the bottom or side of the carburetor.
Here are the general steps to locate and adjust the air/fuel mixture screw:
1. Locate the Carburetor: The carburetor is usually positioned on the side or underside of the engine. Follow the intake manifold or air filter housing to find the carburetor.
2. Identify the Air/Fuel Screw: Look for a small screw on the carburetor. This screw is typically flat-headed and may be recessed. It is often located near the bottom of the carburetor.
3.Adjustment: With the engine running at idle, use a screwdriver to turn the air/fuel mixture screw. Turning it clockwise (in) usually leans out the mixture, while turning it counterclockwise (out) enriches the mixture.
4. Listen to the Engine: As you make adjustments, listen to the engine's sound. The goal is to find the point where the engine runs smoothly and the idle is stable.
5. Fine-Tune: Make small adjustments and give the engine a moment to respond before making further changes. It's a process of trial and error to find the optimal setting.
6. Check the Owner's Manual: Refer to your motorcycle's owner's manual for specific guidance on the location and adjustment of the air/fuel mixture screw. The manual will provide information tailored to your bike's make and model.
If you're uncomfortable making these adjustments yourself or if you're unsure about the location of the screw, it's advisable to consult a professional mechanic or refer to the specific service manual for your Suzuki VS800 Intruder.
11/14/2023 2:14:48 PM •
Suzuki...
•
Answered
on Nov 14, 2023
2005 Suzuki 250 refuse to start even after replacing kickster and battery.
f your 2005 Suzuki 250 is refusing to start even after replacing the kickstarter and battery, there could be several other potential issues to consider. Here are some troubleshooting steps to help you diagnose and resolve the problem:
- Check the Fuel: Ensure that your motorcycle has an adequate supply of fuel in the tank. Sometimes, an empty tank or a clogged fuel filter can prevent the engine from starting.
- Inspect the Spark Plug: A fouled or damaged spark plug can hinder ignition. Remove the spark plug, inspect it for fouling, and replace it if necessary. Also, check the spark plug wire for any damage or loose connections.
- Examine the Air Filter: A dirty or clogged air filter can restrict airflow and affect engine performance. Inspect the air filter, and if it's dirty, clean or replace it.
- Verify the Ignition System: Ensure that the ignition system is functioning correctly. Check for spark by removing the spark plug, grounding it against the engine, and cranking the engine while observing for a spark. If there's no spark, the ignition system may need attention.
- Inspect the Carburetor: A malfunctioning carburetor can cause starting issues. Check for clogs, blockages, or a stuck float valve. Cleaning or rebuilding the carburetor may be necessary.
- Verify the Fuel System: Ensure that fuel is reaching the carburetor. Check for fuel flow by disconnecting the fuel line at the carburetor and cranking the engine briefly. Fuel should flow from the line.
- Compression Test: Low compression can also prevent the engine from starting. Perform a compression test to check the engine's compression levels. If compression is low, it may indicate internal engine problems that require professional attention.
- Electrical Connections: Ensure that all electrical connections are secure, including those to the starter motor and solenoid. Loose or corroded connections can prevent the starter from engaging.
- Safety Switches: Some motorcycles have safety switches like a kickstand switch or a clutch lever switch. Ensure that these switches are not preventing the bike from starting when they shouldn't be.
- Professional Inspection: If you've checked all of the above and still can't identify the issue, it may be best to have a qualified motorcycle mechanic or technician inspect your bike. They have the expertise and tools to diagnose and fix more complex problems.
10/1/2023 11:48:46 AM •
Suzuki...
•
Answered
on Oct 01, 2023
Not finding what you are looking for?