Harley Davidson FLHTCUI Electra Glide Ultra Classic - Recent Questions, Troubleshooting & Support


Hi, Lowell and the usual suspects are:
1. Severely discharged or a damaged battery must have 12.5 volts or more and be able to pass a proper "LOAD" test if necessary, you may have a preliminary reading of 12.5 volts or more but little or zero amperage the battery is faulty and must be replaced, AGM batteries fail in this scenario more so than lead-acid batteries.
2. Faulty alternator/generator and or voltage regulator.
3. Loose or corroded battery terminals and or cables especially the "NEGATIVE" cable, look for loose, corroded, or broken connectors inside the cable harness at "BOTH" ends.
4. Faulty main circuit breaker or ignition switch, check for loose connections and continuity.
5. Faulty system relay or ignition relay, check for continuity.
6. Faulty ignition coil, ignition/electronic module.
7. Faulty CKP, CPS, CMP, MAP, TPS, or BAS sensor, corroded, loose or broken wire connector pins/sockets.
8. Throttle cables and or idle speed improperly adjusted hot idle speed should be 950 RPM to 1000 RPM.
9. Faulty neutral, side stand or clutch lever safety switch.
10. Fuel tank empty
11. Fuel tank contaminated with ethanol sludge.
12. Water or dirt in the fuel system, or clogged filter.
13. Quick disconnect check ball stuck.
14. Restricted, blocked or kinked fuel line.
15. Faulty fuel pump.
16. Faulty pressure regulator.
17. Faulty or clogged fuel injectors.
18. Lean angle switch is faulty or needs adjustment.
19. Catastrophic engine failure, perform a compression test.
For more information about your issue and valuable "FREE" downloads that you need for viewing or printing please click on the blue links below and for more specific information or questions at no charge please feel free to contact me at xlch@mail.com. Good luck and have a wonderful day.
Ultra classic shuts off while riding Harley Davidson Forums
2000 Harley Touring Service Manual pdf
http://partsfinder.onlinemicrofiche.com/ronnies/showmodel.asp?make=hdmc
https://serviceinfo.harley-davidson.com/sip/vehicle/lookupForm
Instant Repair Help over the Phone to speak with me personally $6

2000 Harley... | Answered 3 days ago


Hi, Clifton there is no return fuel line, for this scenario you will need your service manual that has all fastener torque specs and a wiring diagram on the back pages, parts fiche, and owners manual if you can not find the best tool you ever bought for your Harley, despair not, for a mere zero $0 you can download another one.
For more information about your issue and valuable "FREE" downloads that you will need for viewing or printing please click on the blue links below and for more specific information or questions at no charge please feel free to contact me at xlch@mail.com. Good luck and have a wonderful day.
https://www.google.com/search?q=2000+Harley+Davidson+FLHTCUI+Electra+Glide+Ultra+Classic+fuel+line+diagram&tbm=isch&tbo=u&source=univ&sa=X&ved=2ahUKEwjyq4n95dvfAhUQk1kKHcZSAlkQsAR6BAgAEAE&biw=1440&bih=758
http://www.mediafire.com/file/a9pvi3kbxhkfla2/2000+Harley+Touring+Service+Manual.pdf
http://partsfinder.onlinemicrofiche.com/ronnies/showmodel.asp?make=hdmc
https://www.harley-davidson.com/us/en/owners/maintain-your-bike.html
https://www.6ya.com/
To speak to me personally for a mere $6

2000 Harley... | Answered on Jan 07, 2019


Hi, Anonymous sounds more like a wiring connection, before testing any electrical component in the Turn Signal Light Circuit it is "IMPERATIVE" that you have a fully charged battery of 12.5 volts or more and be able to pass a proper "LOAD" test because your battery may have 12.5 volts or more but little or zero amps causing the battery to be faulty and must be replaced, "AGM" batteries fall into this category more so than lead-acid types, also before diagnosing any turn signal/running light/parking light issue make sure the bulb is good and the light fuse has continuity with a test light. If you have replaced your OEM lights with one or all LED lights you are going to need a load equalizer.
If no turn signals are working the cause could be a faulty turn signal module/flasher or the connector going to it, look for, corroded, loose, or broken pins/sockets. Contact spray cleaner is great for removing corrosion.
If your turn signal comes on but takes several seconds before it starts flashing you may have dirty contacts in the turn signal switch/button, the switch needs to be opened up and cleaned also the flasher may be starting to fail. It should be noted that cold weather will only exacerbate the situation especially when temperatures drop down below freezing and the location of the component, turn signal switches on the handlebar are at the mercy of the oncoming freezing 70 mph wind and makes it hard for the contacts to do their job covered in frozen grease/grime
If all four turn signals flash at the same time like hazard lights even though you only pressed one turn signal button then you have a LED light in the circuit and need a load equalizer that can be purchased from any motorcycle parts supplier.
If your speedometer does not function properly it will have to be fixed first because your turn signal module gets the data from the speedometer for normal turn signal function.
If your front turn signals don't work use a test light to check for power and ground at the bulb socket, then start backtracking the wiring through every wire connector to the turn signal switch/button and check for continuity, go all the way back to the fuse if necessary to find the cause of the malfunction.
If your rear turn signals don't work check your rear fender wiring harness connector first, for corroded, broken, loose pins/sockets, power, and a good ground, the harness connector is usually located under the seat on the front of the rear fender then keep tracing the wiring look for obvious harness damage caused by the rear tire.
If you still can't find the malfunction backtrack from the rear fender wiring harness connector.
If one side does not work you could have a faulty turn signal switch or module check for continuity.
For more information about your issue and valuable "FREE" downloads that you will need for viewing or printing please click on the blue links below and for more specific information or questions at no charge please feel free to contact me at xlch@mail.com. Good luck and have a wonderful day.
Help Please Turn signal module problem Harley Davidson Forums 2006 Harley Touring Service Manual pdf http://partsfinder.onlinemicrofiche.com/ronnies/showmodel.asp?make=hdmc 2006 Harley Davidson Ultra Classic Electra Glide EFI Owner Manual Instant Repair Help over the Phone to speak to me personally $4

2005 Harley... | Answered on Oct 29, 2018


Hi, Anonymous for this scenario you will need your service manual that has all fastener torque specs and a wiring diagram on the back pages, parts fiche, and owners manual if you can not find the best tool you ever bought for your Harley, despair not, for a mere zero $0 you can download another one.
For more information about your issue and valuable "FREE" downloads that you will need for viewing or printing please click on the blue links below and for more specific information or questions at no charge please feel free to contact me at xlch@mail.com. Good luck and have a wonderful day.
Self Diagnostics for Harman Kardon radios Harley Davidson Forums
2000 Harley Touring Service Manual pdf
http://partsfinder.onlinemicrofiche.com/ronnies/showmodel.asp?make=hdmc
https://serviceinfo.harley-davidson.com/sip/vehicle/lookupForm free owners manual
Instant Repair Help over the Phone to speak to me personally $4

2000 Harley... | Answered on Oct 16, 2018


Hi, Stephen for this scenario you will need your service manual that has all fastener torque specs and a wiring diagram on the back pages, parts fiche, and owners manual if you can not find the best tool you ever bought for your Harley, despair not, for a mere zero $0 you can download another one.
For more information about your issue and valuable "FREE" downloads that you will need for viewing or printing please click on the blue links below and for more specific information or questions at no charge please feel free to contact me at xlch@mail.com. Good luck and have a wonderful day.
2008 Harley Davidson FLHTCU speed sensor location Google Search
2009 Harley FSXTC Speed sensor removal and replacement part
2008 Harley Touring Service Manual pdf
http://partsfinder.onlinemicrofiche.com/ronnies/showmodel.asp?make=hdmc
2008 Harley Davidson Ultra Classic Electra Glide Owner Manual

2005 Harley... | Answered on Oct 05, 2018


Hi, Minions PN numbers is not a fault code they usually show up at the end of a diagnostic search for generated error codes that are active or non-active that have been resolved but not cleared. They are part numbers that identify electrical components that are currently installed on the bike. 32919-07 is the ECM that has been remapped for a stage one upgrade. 68925-07 is the turn signal security alarm module. 67349-04 is the speedometer.
For more information about your issue and valuable "FREE" downloads that you will need for viewing and printing please click on the links below and for more specific information or questions at no charge please feel free to contact me at xlch@mail.com. Good luck and have a nice day.
Harley Diagnostic Codes 04 Present DG Custom Cycle
2006 Harley Touring Service Manual pdf
http://partsfinder.onlinemicrofiche.com/ronnies/showmodel.asp?make=hdmc
2006 Harley Davidson Ultra Classic Electra Glide EFI Owner Manual
Instant Repair Help over the Phone to speak to me personally $4

2005 Harley... | Answered on Sep 25, 2018


Hi, Gary for this scenario you will need your service manual that has all fastener torque specs and a wiring diagram on the back pages, parts fiche, and owners manual if you can not find the best tool you ever bought for your Harley, despair not, for a mere zero $0 you can download another one.
For more information about your issue and valuable "FREE" downloads that you will need for viewing or printing please click on the blue links below and for more specific information or questions at no charge please feel free to contact me at xlch@mail.com. Good luck and have a wonderful day.
How to get to the fuse panel on Harley Davidson Electra Glide Motorcycle
2005 Harley Touring Service Manual pdf
http://partsfinder.onlinemicrofiche.com/ronnies/showmodel.asp?make=hdmc
2005 Harley Davidson Electra Glide Classic EFI Owner Manual
Instant Repair Help over the Phone to speak to me personally $4

2005 Harley... | Answered on Sep 05, 2018


Hi, Diane and the usual suspects are:
1. Improper installation.
2. Speedometer cable pinched, kinked, or the inner cable is rusted
For this scenario, you will need your service manual, parts fiche, and owners manual if you can not find the best tool you ever bought for your Harley, despair not, for a mere zero $0 you can download another one.
For more information about your issue and valuable "FREE" downloads that you will need for viewing or printing please click on the blue links below and for more specific information or questions at no charge please feel free to contact me at xlch@mail.com. Good luck and have a wonderful day.
84 to 98 FL FX Harley Service Manual pdf
http://partsfinder.onlinemicrofiche.com/ronnies/showmodel.asp?make=hdmc
https://serviceinfo.harley-davidson.com/sip/vehicle/lookupForm free owners manual
Harley Davidson FLHTCUI Electra Glide Ultra Classic Injection 1998...
Harley Davidson FL

2000 Harley... | Answered on Aug 02, 2018


Hi, Kevin I hate when that happens and the usual suspects are:
1. Severely discharged or a damaged battery must have 12.5 volts or more and be able to pass a proper "LOAD" test if necessary, you may have a preliminary reading of 12.5 volts or more but little or zero amperage the battery is faulty and must be replaced, AGM batteries fail in this scenario more so than lead-acid batteries.
2. Faulty alternator/generator and or voltage regulator.
3. Loose or corroded battery terminals and or cables especially the "NEGATIVE" cable, look for loose, corroded, or broken connectors inside the cable harness at "BOTH" ends.
4. Faulty main circuit breaker or ignition switch, check for loose connections and continuity.
5. Faulty system relay or ignition relay, check for continuity.
6. Faulty ignition coil, ignition/electronic module.
7. Faulty CKP, CPS, CMP, MAP, TPS, or BAS sensor, corroded, loose or broken wire connector pins/sockets.
8. Throttle cables and or idle speed improperly adjusted hot idle speed should be 950 RPM to 1000 RPM.
9. Faulty neutral, side stand or clutch lever safety switch.
10. Fuel tank empty
11. Fuel tank contaminated with ethanol sludge.
12. Water or dirt in the fuel system, or clogged filter.
13. Quick disconnect check ball stuck.
14. Restricted, blocked or kinked fuel line.
15. Faulty fuel pump.
16. Faulty pressure regulator.
17. Faulty or clogged fuel injectors.
18. Lean angle switch is faulty or needs adjustment.
19. Catastrophic engine failure, perform a compression test.
For more information about your issue and valuable "FREE" downloads that you need for viewing or printing please click on the blue links below and for more specific information or questions at no charge please feel free to contact me at xlch@mail.com. Good luck and have a wonderful day.
Ultra classic shuts off while riding Harley Davidson Forums
84 to 98 FL FX Harley Service Manual pdf
http://partsfinder.onlinemicrofiche.com/ronnies/showmodel.asp?make=hdmc
https://serviceinfo.harley-davidson.com/sip/vehicle/lookupForm free owners manual
Instant Repair Help over the Phone to speak to me personally $4

Harley Davidson... | Answered on Jul 28, 2018


Hi, Hugh for this scenario you will need your service manual that has all fastener torque specs and a wiring diagram on the back pages, parts fiche, and owners manual if you can not find the best tool you ever bought for your Harley, despair not, for a mere zero $0 you can download another one.
For more information about your issue and valuable "FREE" downloads that you will need for viewing or printing please click on the blue links below and for more specific information or questions at no charge please feel free to contact me at xlch@mail.com. Good luck and have a wonderful day.
Radio Display Screen BLANK Harley Davidson Forums
2015 Harley Touring Service Manual pdf
http://partsfinder.onlinemicrofiche.com/ronnies/showmodel.asp?make=hdmc
2015 Harley Davidson Electra Glide Ultra Classic Owner Manual Instant Repair Help over the Phone to speak to me personally $4

Harley Davidson... | Answered on Jul 21, 2018


Hi, Anonymous inside the fuel tank for this scenario you will need your service manual, parts fiche, and owners manual if you can not find the best tool you ever bought for your Harley, despair not, for a mere zero $0 you can download another one.
For more information about your issue and valuable "FREE" downloads that you will need for viewing or printing please click on the blue links below and for more specific information or questions at no charge please feel free to contact me at xlch@mail.com. Good luck and have a wonderful day.
2000 Harley Davidson FLHTCUI Electra Glide Ultra Classic fuel pump...
2000 Harley Touring Service Manual pdf
http://partsfinder.onlinemicrofiche.com/ronnies/showmodel.asp?make=hdmc
https://serviceinfo.harley-davidson.com/sip/vehicle/lookupForm Instant Repair Help over the Phone speak with me personally $4

2000 Harley... | Answered on Jul 21, 2018


Hi, Anonymous for this scenario you will need your service manual that has all fastener torque specs and a wiring diagram on the back pages, parts fiche, and owners manual if you can not find the best tool you ever bought for your Harley, despair not, for a mere zero $0 you can download another one.
For more information about your issue and valuable "FREE" downloads that you will need for viewing or printing please click on the blue links below and for more specific information or questions at no charge please feel free to contact me at xlch@mail.com. Good luck and have a wonderful day.
Checking Oil Level on Your Harley Davidson Harley Davidson Forums
2003 Harley Touring Service Manual pdf
http://partsfinder.onlinemicrofiche.com/ronnies/showmodel.asp?make=hdmc
2005 Harley Davidson Electra Glide Ultra Classic EFI Owner Manual
Instant Repair Help over the Phone To speak to me personally for a mere $4

2003 Harley... | Answered on Jul 11, 2018


Hi, Bill and the usual suspects are:
1. Faulty ignition coil.
2. Faulty spark plug cables.
3. Faulty temperature sensor.
4. Faulty starter motor.
5. Valves adjusted too tight.
6. Spark plug gap too wide.
7. Fuel line has a vapor lock.
For more information about your issue and valuable "FREE" downloads that you will need for viewing or printing please click on the blue links below and for more specific information or questions at no charge please feel free to contact me at xlch@mail.com. Good luck and have a wonderful day.
Hard Start When Hot Harley Davidson Forums
2002 Harley Touring Service Manual pdf
http://partsfinder.onlinemicrofiche.com/ronnies/showmodel.asp?make=hdmc
https://serviceinfo.harley-davidson.com/sip/vehicle/lookupForm free owners manual
Instant Repair Help over the Phone To speak to me personally for a mere $4

2002 Harley... | Answered on Jul 09, 2018


Hi, Archie for this scenario you will need your service manual that has all fastener torque specs and a wiring diagram on the back pages, parts fiche, and owners manual if you can not find the best tool you ever bought for your Harley, despair not, for a mere zero $0 you can download another one.
For more information about your issue and valuable "FREE" downloads that you will need for viewing or printing please click on the blue links below and for more specific information or questions at no charge please feel free to contact me at xlch@mail.com. Good luck and have a wonderful day.
Rear axle nut torque Harley Davidson Forums
Bolt Torque Values
84 to 98 FL FX Harley Service Manual pdf
http://partsfinder.onlinemicrofiche.com/ronnies/showmodel.asp?make=hdmc
https://serviceinfo.harley-davidson.com/sip/vehicle/lookupForm free owners manual
Instant Repair Help over the Phone To speak to me personally for a mere $4

2000 Harley... | Answered on Jun 30, 2018


Hi, Anonymous Harley Davidson uses medium carbon heat treated steel Grade 5 fasteners these are the most common torque specifications in foot pounds for dry threads.
Size____Grade 2__________Grade 5_____________Grade 8
1/4_______6________________10_________________14
5/16______12_______________19_________________25
3/8_______20_______________33_________________44
7/16______32_______________54_________________71
1/2_______47_______________78_________________110
For more information about your issue and valuable "FREE" downloads that you will need for viewing or printing please click on the blue links below and for more specific information or questions at no charge please feel free to contact me at xlch@mail.com. Good luck and have a wonderful day.
Bolt Torque Values
2006 Harley Touring Service Manual pdf
http://partsfinder.onlinemicrofiche.com/ronnies/showmodel.asp?make=hdmc
2006 Harley Davidson Ultra Classic Electra Glide EFI Owner Manual
6ya Instant Expert Help To speak to me personally absolutely free

2005 Harley... | Answered on Jun 18, 2018


Hi, GeorgeBacon for this scenario you will need your service manual that has all fastener torque specs and a wiring diagram on the back pages, parts fiche, and owners manual if you can not find the best tool you ever bought for your Harley, despair not, for a mere zero $0 you can download another one.
For more information about your issue and valuable "FREE" downloads that you will need for viewing or printing please click on the blue links below and for more specific information or questions at no charge please feel free to contact me at xlch@mail.com. Good luck and have a wonderful day.
2006 Harley Davidson FLHTCUI Electra Glide Ultra Classic wiring diagram...
2006 Harley Touring Service Manual pdf
http://partsfinder.onlinemicrofiche.com/ronnies/showmodel.asp?make=hdmc
2006 Harley Davidson Ultra Classic Electra Glide EFI Owner Manual
6ya Instant Expert Help To speak to me personally absolutely free

2005 Harley... | Answered on Jun 18, 2018


Hi Anonymous, always check your instrument fuse before performing the next procedure, try cleaning your speed sensor located on top of the transmissions right side between the top cover and the chrome starter end cap on Twin Cams and on top of the engine case between the rear cylinder and the starter motor for Sportsters. Remove the the bolt that secures the sensor and pull it out of the transmission. Inspect sensor for obvious damage and repace if necessary. If sensor has no damage then wipe clean any obvious contamination like micro fiberous material with a clean rag and reinstall, torque bolt to 8 ft lbs. Next check the connector to the speedometer for correded, broken or loose pins/sockets. Good luck and have nice day.

Btw, I’m available to help over the phone in case u need at https://www.6ya.com/expert/gregg_c0ec1df182c7330e

2001 Harley... | Answered on Jun 12, 2018


Hi, Edward for this scenario you will need your service manual that has all fastener torque specs and a wiring diagram on the back pages, parts fiche, and owners manual if you can not find the best tool you ever bought for your Harley, despair not, for a mere zero $0 you can download another one.
For more information about your issue and valuable "FREE" downloads that you will need for viewing or printing please click on the blue links below and for more specific information or questions at no charge please feel free to contact me at xlch@mail.com. Good luck and have a wonderful day.
Set Change Override Transport Harley Security Alarm PIN Code No Key Fob...
2001 Harley Touring Service Manual pdf
http://partsfinder.onlinemicrofiche.com/ronnies/showmodel.asp?make=hdmc
https://serviceinfo.harley-davidson.com/sip/vehicle/lookupForm free owners manual
6ya Instant Expert Help To speak to me personally absolutely free

2001 Harley... | Answered on Jun 12, 2018


Hi, Gary you may have disturbed the pressure regulator causing insufficient fuel pressure for this scenario you will need your service manual that has all fastener torque specs and a wiring diagram on the back pages, parts fiche, and owners manual if you can not find the best tool you ever bought for your Harley, despair not, for a mere zero $0 you can download another one.
For more information about your issue and valuable "FREE" downloads that you will need for viewing or printing please click on the blue links below and for more specific information or questions at no charge please feel free to contact me at xlch@mail.com. Good luck and have a wonderful day.
Harley Davidson Magneti Marelli Fuel Injection Settings
84 to 98 FL FX Harley Service Manual pdf
http://partsfinder.onlinemicrofiche.com/ronnies/showmodel.asp?make=hdmc
https://serviceinfo.harley-davidson.com/sip/vehicle/lookupForm free owners manual
6ya Instant Expert Help To speak to me personally absolutely free

Harley Davidson... | Answered on Jun 10, 2018


Hi, David excellent question, before I begin let me address motorcycles with valves and seats designed to run on leaded fuel issue, you can run unleaded fuel without a lead additive with no problem just replace the valves and seats with ones designed for unleaded fuel the next time you need a top end overhaul. In extremely rare cases some higher compression engines will ping using the highest octane graded unleaded fuel available in these cases the use of a lead additive or aviation fuel is recommended. Octane rating is a measure of a fuel's ability to resist 'knock'. The octane requirement of an engine varies with compression ratio, geometrical and mechanical considerations and operating conditions. The higher the octane number the greater the fuel's resistance to knocking or pinging during combustion.
The recommended octane rating for most motorcycles is usually octane 87, but be sure to check your bike's owner's manual. Ordinarily, your motorcycle will not benefit from using an octane higher than recommended in the owner's manual. However, some motorcycle models have high-compression engines and electronic controls, which are designed to benefit from the greater power output and improved fuel economy of high-octane fuel. Since octane requirements can vary with operating and environmental conditions, your bike may need a higher octane fuel than recommended to prevent knocking.
Bottom line, use the lowest grade octane that gives you acceptable performance without knocking or pinging.
For more information about your issue and valuable "FREE" downloads that you will need for viewing or printing please click on the blue links below and for more specific information or questions at no charge please feel free to contact me at xlch@mail.com. Good luck and have a wonderful day.
Fuel Octane what best Twin Forum Harley Davidson Forums
1999 Harley Touring Service Manual pdf
http://partsfinder.onlinemicrofiche.com/ronnies/showmodel.asp?make=hdmc
https://serviceinfo.harley-davidson.com/sip/vehicle/lookupForm free owners manual
Instant Tech Relief To speak to me personally absolutely free

2000 Harley... | Answered on May 25, 2018

Not finding what you are looking for?

57 questions posted

Ask a Question

Usually answered in minutes!

Top Harley Davidson Experts

Gar
Gar

Level 2 Expert

384 Answers

Arnie Burke
Arnie Burke

Level 3 Expert

5809 Answers

Mike

Level 3 Expert

4356 Answers

Are you a Harley Davidson Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

View Most Popular

Harley Davidson Motorcycles

  • Forum

View Most Popular

  • Harley Davidson Motorcycles
Loading...