1995 Toyota Supra Logo

Related Topics:

Posted on Jul 04, 2008

3S-SFE Engine I have this engine on my Vista D4 and the front crancshaft gear broke but when we put it back the engine cant start dispite timing it properly. Can anyone help Gwatula

  • Austin Chimwaza
    Austin Chimwaza Mar 18, 2019

    Can you explain the timing specs which you used

×

1 Answer

Anonymous

Level 1:

An expert who has achieved level 1.

  • Contributor 1 Answer
  • Posted on Jan 06, 2009
Anonymous
Contributor
Level 1:

An expert who has achieved level 1.

Joined: Sep 24, 2008
Answers
1
Questions
3
Helped
323
Points
4

Check the crankshaft sensor on your right hand when viewing the crank gear. Maybe yo broke it when removing the gear or you unplug the connector.

Add Your Answer

×

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

0helpful
1answer

Toyota Nadia 3s-fse-d4 Fan belt and a/c belt numbers

For the Toyota Nadia with the 3S-FSE-D4 engine, you can find the fan belt and A/C belt using the following specifications:

1. Fan Belt:
- The fan belt for the 3S-FSE-D4 engine should have the following specifications, which you can use to find a replacement:
- Part Number: 90916-02400
- Dimensions: 6PK1955 (6 ribs, 1955mm length)

2. A/C Belt:
- The A/C belt for the 3S-FSE-D4 engine should have the following specifications:
- Part Number: 99364-20840
- Dimensions: 5PK1060 (5 ribs, 1060mm length)

When replacing the belts, it's important to ensure that they are installed with the correct tension to prevent any high pitched noises or premature wear. If the belts are making a high pitched noise, it could indicate either wear or improper tension. It's recommended to inspect the belt tensioner and pulleys for any signs of wear or damage while replacing the belts.

Additionally, it's a good practice to check for any misalignment of the pulleys as this could also cause excessive noise and premature wear on the belts. Once the new belts are installed, check the tension according to the manufacturer's specifications to ensure proper operation and minimize noise. If the noise persists after belt replacement, further inspection of the A/C compressor and other related components may be necessary.
0helpful
2answers
0helpful
2answers

Toyota vista d4 engine runs then shuts after a while drive.cools down then starts again.3s-fse

It seems somebody tempered with the throttlebody air adjustment so whenever the car heats up they will be more air supplied to mix with fuel it blows the fuel out plus the heat coming makes the car does what we call preignition rendering the cylinder useless at the point of combustion but after it cools down with the air switch automatically switched off for cold start it will run
3_19_2017_9_54_05_am.jpg
0helpful
1answer

How do I time a 3S d4 Toyota corona engine?

i moved you out of JEEPS
its not a JEEP
new year, car.
fail 2 times.
books start with year, see?'
online or real.
same.
0helpful
1answer

How do I reset the engine management unit and reset the check engine light. Toyota Vista Ardeo 1999 3S-FSE D4

When a battery is drained like that control modules lose memory ,thing's need to be relearned ! Battery Disconnect or Replacement Problems European vehicles are the worst for this
0helpful
1answer

The speedometer on my 1998 toyota D4 corona premio, 3s engine, suddenly drops when i step on the accelerator with the intention of increasing my speed. when i try to speed up the vehicle almost stops but...

GAS
3s-fse-d4-engine???? 3s-GE OR GE WITH RED BEAM? "VVT"
M./T OR A/T (STICK OR AUTO)
the key factor is engine RPM
if it rises, but not speed, that is trans./clutch slip
if no rpm rise that is weak engine , BUT IS THE RED BEAM.?

LOW POWER, 101
1: NEVER TUNED UP. BAD SPARK CLOGGED FILTES X2
2: ENGINE ecu stuck in limphome, scan it, see errors, BINGO
3: engine misfiring, cause by low compression, weak spark or bad fueling (too rich or too lean) many tests, ask.
4: low fuel pressure or regulator not regulation per FsM PAGE
5:STUCK OPEN egr main valve (missing in some countries)
6: melted cat converter , vacuum gage reads real bad,
7: and more, i charge more for more, LOL vvt?

ask or tell?
i want wild guessing
or I want to do the tests. to find it.

Gue$$ or Test.
toss coin.?


1helpful
3answers

I am in Zimbawe how do i get the manual for 3s-FSE D4 2.0L engine manual. Please help am very desparate. My email is [email protected]

Dont have a manual for this vehicle but if you need any help with anything in particualr just reply to this post .
0helpful
1answer

Can anyone please help me with pics or detailed desription on were the timing marks should be on a toyota d4 3s-fse engine, i need to know how to place the two cams and also the timing mark on the cam...

Welcome to FIxYa.com


Need the year and model and size as in liter engine in order to look this up for you to send pic and info. Engine number does not work in Alldata, Lee


Thank you for using FixYa.com

Regards, Lee Davidian

8helpful
3answers
Not finding what you are looking for?

333 views

Ask a Question

Usually answered in minutes!

Top Toyota Experts

ZJ Limited
ZJ Limited

Level 3 Expert

17989 Answers

Thomas Perkins
Thomas Perkins

Level 3 Expert

15088 Answers

ROBERT GARCIA
ROBERT GARCIA

Level 3 Expert

926 Answers

Are you a Toyota Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...