I have a 1999 Ford SHO that needs a new waterpump. I need to know how to replace it and where I can get a schematic of it. Do I need a special tool kit to do it? I'd also like to know where I can get the part in the state of washington?

Www.autozone.com

They can get all the parts. They also provide haynes repair manuals, any special tools (probably not required for this vehicle) and any special disassembly instructions.

I hope this helps.

Water Pump Removal

1. Drain engine cooling system. Refer to Section 03-03 .
   

1. Remove engine appearance cover as described in this section.
   

1. Remove battery (10653) and battery tray (10732) . Refer to Section 14-01 .
   

1. Remove drive belt (8620) from water pump (8501) and water pump pulley (8509) .
   

1. Disconnect water bypass tube (8548) , heater core return hose and oil cooler return hose from water pump .
   

1. Remove two bolts retaining water hose connection (8592) to water pump housing. Pull water hose connection away from water pump and remove water thermostat (8575) from water pump housing.
   

1. Remove bolts and collar retaining water pump housing to LH cylinder head (6049).
   

1. Disconnect water outlet hose and water inlet hose from water pump and remove water pump from engine.
   

1. Remove retaining bolt and belt idler pulley (8678) from water pump housing.
   

1. Inspect water pump for wear or damage. Replace components as required.
   Installation
   
   1. Clean water pump-to-water pump housing gasket sealing surfaces.
      
   1. If removed, install water pump belt idler pulley and retaining bolt to water pump housing. Tighten retaining bolt to 10-16 Nm (89-141 lb-in).
      
   1. Lubricate water pump inlet hose, outlet hoses and O-ring with Ford Extended Life Engine Coolant F6AZ-19544-AA or DEX-COOL® equivalent that meets Ford specification WSS-M97B44-D. Install water pump inlet and outlet hoses onto water pump housing. Install water pump outlet hose spring clamp securely.
      
   1. Place O-ring between water pump housing and LH cylinder head.
      
   1. Install bolts retaining water pump housing to LH cylinder head . Tighten two retaining bolts at water inlet to 8-12 Nm (71-106 lb-in). Tighten two remaining retaining bolts to 18-28 Nm (14-20 lb-ft).
      
   1. Install water thermostat, oil cooler return tube gasket (6N789) and water hose connection to water pump housing with two retaining bolts. Tighten to 8-12 Nm (71-106 lb-in).
      
   1. Install throttle body return and supply hoses, heater core return hose and oil cooler return hose to water pump .
      
   1. Install water pump drive belt. Carefully release drive belt tensioner (6B209) . Refer to Section 03-05 .
      
   1. Fill engine cooling system. Refer to Section 03-03 .
      
   1. Install engine appearance cover as described.
      
   1. Install battery trayand battery . Refer to Section 14-01 .
      
   1. Run engine and check for coolant leaks.
      
   Item Part Number Description 1 8A577 Water Outlet Hose 2 8548 Throttle Body to Water Pump Return Hose 3 8548 Water Pump to Throttle Body Supply Hose 4 95827-08110 Bolt 5 8501 Water Pump (2 Req'd) 6 8575 Water Thermostat 7 6N789 Oil Cooler Return Tube Gasket 8 8592 Water Hose Connection 9 95827-06020 Bolt 10 8287 Heater Core to Water Pump Return Hose 11 90116-08604 Stud 12 6B851 Oil Cooler to Water Pump Return Hose 13 8620 Drive Belt (2 Req'd) 14 95817-06045 Bolt 15 8678 Belt Idler Pulley 16 6A359 Water Pump Drive Pulley 17 90387-082T8 Collar 18 8K540 O-Ring 19 8548 Water Inlet Hose 20 95827-06025 Bolt A — Tighten to 18-28 Nm (14-20 Lb-Ft) B — Tighten to 10-16 Nm (89-141 Lb-In) C — Tighten to 8-12 Nm (71-106 Lb-In)