2004 AVALON DRIVWER SIDE MIRROR 11 WIRES I WANT TO REPLACE WITH AFTER MARKET MIRROR W HEATHER NO MEMORY PLEASE SEND A WIRING DIAGRAM ?

MOVED YOU FROM WASHING MACHINES TO CARS. PROPER.
all you do is match coolers
if not sure, that the service manual covers all that.
seen here
my guess car lighting failure of some kind, parks , heads but front or rear not told, fender side, sure. but which corner of car sure left side USA or Right side UK?

one of the best of 3 , USA, are you USA?
https://eautorepair.net/Marketing/Default.asp

http://www.fordaustraliaforums.com/forum/showthread.php?50606-Need-wiring-diagram-for-au-11-ford-2002-for-stereo-please-help

there are two links on the second post.

no symptoms posted (broke glass or ???) can we be on same page?
"how do I switch," verb switch , the mirror as switches inside, too.

please say what that word means. switch and the failure.
1: remove and replace with new.
2: move right to left and left to right side.

why would you do that #2
fold away mirrors/ Export only (this is usa forum so..)
these,NASA grade mirrors are very complex... not just glass and plastic. heaters ,motors, memory , etc.

the FSM cover all tests for the mirror, including scan data.

ill quote the FSM now , 8 steps (just 1 fail,not heat, not memory failure or fold failure)
ONE MIRROR INOPERATIVE
(1) If the one inoperative mirror is on the passenger
side, go to Step 2. If the one inoperative mirror is
on the driver side, go to Step 3.
(2) Check if the passenger front door will lock and
unlock using the power lock switch on the driver side
front door. If OK, go to Step 3. If not OK, go to Step 6.
(3) Disconnect and isolate the battery negative
cable. Remove the trim panel from the front door.
Disconnect the 12-way mirror wire harness connector
from the door wire harness connector.
(4) Using two jumper wires, test the mirror as
shown in the Mirror Test chart (Fig. 2). If the mirror
tests OK, go to Step 5. If the mirror does not test
OK, replace the faulty mirror.
(5) Disconnect the 12-way door wire harness connector
from the door module connector receptacle.
Check all of the circuits of the door wire harness
between the connector for the mirror and the connector
for the door module for opens or shorts. If all of
the circuits are OK, replace the faulty door module.
If any of the circuits are not OK, repair the open or
shorted circuit(s) as required.
(6) Use a DRB scan tool and the proper Diagnostic
Procedures manual to test and repair the faulty Programmable
Communications Interface (PCI) data bus
communication between the two door modules.

(bar stool answer) all cars. mostly
pull door skins
unplug motor conn.
unscrew mirror base from door.
extract mirror,

This radio wiring diagram may help you to figure out where that wiring job went wrong. Use it along with the diagram that came the aftermarket radio to make sure that you got all the wires in the proper places.

2002 Toyota Avalon wiring diagram, my friend cut the harness thinking he knew what he was doing so now I'm trying to replace the harness but do not know the right diagram colors

if you have checked all your fuses try tracing the wiring back to fuse box last time i had this problem it was in the wiring just out of the fuse box

My manual for a 99 300M shows two sources of 12 volt power to the mirror positioning switch, One is from the battery, switch terminal 11 wire M1, PK (pink). The other is from the start-run 12 volt line, switch terminal 5, wire G5 DB/WT (dark blue, white stripe). If you send me your email address to af6im at arrl dot net I can send you a scanned copy of the diagram.

Heated mirrors usually have a symbol on them -- a small diagram showing squigley heat lines.

If you don't see this, it's probably not heated. But when you take the mirror off, if it's heated it'll have wires connected to the back.

Yes, you can replace a heated mirror with non-heated -- just leave the wires tucked out of the way when you install the new mirror.