Cars & Trucks Logo

Related Topics:

Todd Kalland Posted on Mar 14, 2019
Answered by a Fixya Expert

Trustworthy Expert Solutions

At Fixya.com, our trusted experts are meticulously vetted and possess extensive experience in their respective fields. Backed by a community of knowledgeable professionals, our platform ensures that the solutions provided are thoroughly researched and validated.

View Our Top Experts

05 Lincoln LS driver door does not luck/unlock using remote keyless entry.

  • Todd Kalland
    Todd Kalland Mar 15, 2019

    All other doors and trunk work fine using the remote key fob.

×

1 Answer

Brad Brown

Level 3:

An expert who has achieved level 3 by getting 1000 points

Superstar:

An expert that got 20 achievements.

All-Star:

An expert that got 10 achievements.

MVP:

An expert that got 5 achievements.

  • Lincoln Master 19,187 Answers
  • Posted on Mar 14, 2019
Brad Brown
Lincoln Master
Level 3:

An expert who has achieved level 3 by getting 1000 points

Superstar:

An expert that got 20 achievements.

All-Star:

An expert that got 10 achievements.

MVP:

An expert that got 5 achievements.

Joined: Nov 14, 2008
Answers
19187
Questions
0
Helped
4344789
Points
82261

Check the battery on the remote key FOB. There are places like autozone etc, that can do this for you. If it is not the battery then you are looking at a problem with either the FOB transmitter or the BODY CONTROL MODULE in the vehicle.

5 Related Answers

Anonymous

  • 192 Answers
  • Posted on Apr 05, 2009

SOURCE: Honda Civic 2002 keyless entry

inspect and or replace the drivers door lock actuator...

Ad

Anonymous

  • 365 Answers
  • Posted on Jun 14, 2009

SOURCE: Keyless Entry won't Lock/Unlock back door

Factory keyless?

Anonymous

  • 521 Answers
  • Posted on Aug 13, 2009

SOURCE: 2001 subaru impreza WRX unlocking doors with key

usually after opening the door you can deactivate the alarm by pushing th unlock button or simply insert keyy in ignition and turn it on.

Anonymous

  • 18 Answers
  • Posted on Nov 22, 2009

SOURCE: lost keyless entry remote

turn door lock left twice to un do alarm ,on old cars it may or may not work due to old age

emissionwiz

Marvin

  • 85242 Answers
  • Posted on Mar 07, 2010

SOURCE: error code p 1633 on 2000 lincoln ls

P1633 Keep Alive Power Voltage Too Low (Ford) It means that at sometime in the past the battery voltage was below specs at the PCM and set the code.The battery provides 12 volts to power everything,the car probably sat for a while and probably took a long time to start or had to be jumped off to start.... when the voltage got below 9 volts it set the code. The code is more of a indicator for us more than anything.. the computer learns as you drive and all the code is saying is that it lost it's power to itself and can loose that learned information. Have a shop inspect the battery for being weak or dying as well as your battery connections.. if all is fine, I wouldn't worry as my guess is the car's code was set cause it sat unused for a while

Ad

Add Your Answer

×

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

0helpful
1answer

WHAT IS THE SEQUENCE OF #"S TO PUSH ON A 2004

If you have some "new" key, could try to re-programed and synchonized, you must have all remote entry transmitters (maximum of four) available before beginning this procedure. To reprogram the remote entry transmitters (accordign with the Lincoln LS Owners Manual) :
1. Ensure the vehicle is electronically unlocked.
2. Put the key in the ignition.
3. Turn the key from the 1 (LOCK) position to 4 (RUN).
4. Cycle eight times rapidly (within 10 seconds) between the 1 (LOCK) position and 4 (RUN). Note: The eighth turn must end in the 4 (RUN) position.
5. The doors will lock, then unlock, to confirm that the programming mode has been activated.
6. Within 20 seconds press any button on the remote entry transmitter.

Note: If more than 20 seconds have passed you will need to start the procedure over again.

Hope this helps (remember to rating this answer and leave a testimonial comment).
0helpful
1answer

The door lock on driver side front doesn't work anymore with the remote, the other doors are working fine on a Lincoln Ls 2004

Try using the Keyless Entry Pad

If that won't open the drivers door,
then you will need a scan tool, to see
if it can comunicate with the DDM -
Drivers Door Module.

That may be a possible problem, if
everything else works
0helpful
1answer

My 2000 Lincoln LS keyless remote doesn't work, so I replaced the $15.89 battery and still nothing from what Ive read on this site keyless entry keypad remote code should be in the manual but...

You have to go to a lincoln dealer with your title
& Vin #,they will give you the factory code for the
Keyless Entry on the drivers door

Make sure you have them write down to proceedure
that was in the owners manual ,so you can change it
to what you want.

I have a 2004 LS I don't know if it is the same.
Have no way to scan it & send it to you
0helpful
3answers

LHJ001 WIRING

I have the 1995-97 Lincoln Continental Alarm, Remote Starter, Keyless Entry Wiring, review it:

b94b6e9.png


Hope helped.
1helpful
1answer

Cannot find code for keyless enrty pad on door on a 2003 linclon

you have to contact the dealer.then give them the VIN number they are the only ones that have it
1helpful
2answers

1999 lincoln con

SECTION 501-14B: Keyless Entry/Computer Operated Locks 1999 Town Car Workshop Manual GENERAL PROCEDURES Programming —Keyless Entry Keypad Code
  1. Enter the permanent factory keyless entry keypad code.
  1. Press the 1/2 button within five seconds to activate the programming mode. Holding the 1/2 button for more than two seconds will erase all stored customer codes. The existing codes do not need to be erased to program new codes.
  1. Enter the new five-digit keyless entry keypad code.
  1. To associate the new code with personality positions 1, 2 or 3, press the 1/2 button within 5 seconds of entering the 5th digit of the new code for position 1 or 3/4 button for position 2 or 5/6 for position 3. The door locks will lock and unlock confirming the new code is programmed.
  1. If another code is to be programmed, begin entering the code within 5 seconds of the last button pressed.
  1. After all new keyless entry codes are programmed:
    • Press keyless entry keypad buttons 7/8 and 9/0 at the same time to exit the program mode.
    • Wait for 5 seconds; the driver door module (DDM) will exit the program mode automatically.
    • -------------------------------------------------------------
Programming —Transmitter
  1. Cycle the ignition from OFF to RUN four times within three seconds. The locks will then lock and unlock, confirming program mode has been entered.
  1. NOTE: When the first keyless entry remote transmitter is programmed, all other keyless entry remote transmitters are erased.
    Press any button on the transmitter to be programmed.
  1. If additional keyless entry remote transmitters are to be programmed, repeat step 2 within 7.5 seconds.
  1. To exit program mode, turn the ignition to START or wait 7.5 seconds.
--------------------------------------------------
Programming —Remote Memory Activation NOTE: This procedure must be completed within 5 seconds.
  1. Press the SET button on the driver door panel.
  1. Press any button on the keyless entry remote transmitter to be associated with a memory setting.
  1. Press the 1 or 2 memory button on the driver door panel.
-------------------------------------------------------------
Programming —Autolock and Horn Chirp
  1. NOTE: This procedure must be completed within 30 seconds.
    Turn the ignition switch to RUN.
  1. Press the UNLOCK button three times.
  1. Turn the ignition switch to OFF.
  1. Press the UNLOCK button three times.
  1. Turn the ignition switch to RUN. The doors will lock and unlock to confirm entry into program mode.
  1. Press the UNLOCK button once to toggle the Autolock feature on or off, or twice to toggle the Horn Chirp function on or off. The horn will chirp to confirm toggling of the Autolock feature.
  1. Exit program mode by turning the ignition to OFF, START, or wait 7.5 seconds.
----------------------------------------------------------------------------------
0helpful
2answers

My remote for the keyless entry does not work.

does trunk button work? panic button?
here's 2003 info:


  • The doors do not lock/unlock using the remote transmitter
  • Remote transmitter.
  • Driver door module (DDM).
  • Go To Pinpoint Test G .

SECTION 501-14: Handles, Locks, Latches and Entry Systems 2003 Town Car Workshop Manual
GENERAL PROCEDURES Remote Transmitter Programming
  1. Cycle the ignition from OFF to RUN four times within three seconds. The locks will then lock and unlock, confirming that the program mode has been entered.
  1. NOTE: When the first keyless entry remote transmitter is programmed, all other keyless entry remote transmitters are erased.
    Press any button on the transmitter to be programmed.
  1. If additional keyless entry remote transmitters are to be programmed, repeat Step 2 within 7.5 seconds.
  1. To exit program mode, turn the ignition to START or wait 7.5 seconds.
--------------------------------------------------------------
report back
0helpful
1answer

Lincoln LS keyless entry problem

you half to take it to a ford dealer and have the remote reprogramed to the car.
2helpful
2answers

Reprogram a keyless entry remote

Hello
this is how to program the remotes/keyless entry

How
  • Obtain all remote transmitters
  • enter the 5 digit permanent code into the keyless entry pad on the drivers door
  • Press the 1-2 switch on the keyless entry pad
  • Within 5 seconds
  • Press any button on the first remote transmitter
  • The doors should open then lock
  • Within 5 seconds
  • press any button on the second & third remote
  • within 5 seconds for each remote
  • to exit programming
  • simultanionusly press 7-8 & 9-0 switchs on the key pad or wait more then 7.5 seconds
NOTE
The 5 digit permanent code is located in one of the following places
  1. On the owners warranty card
  2. On the label on the inside the trunk/ boot
  3. On the owners code card
  4. On the centrel locking control module located in the drivers door
  5. In the PCM ford can get this for about $25.00
I hope this help
Regards Paul
www.limotec.co.uk
13helpful
6answers

Keyless entry stopped working on 05 cobalt now i have to unlock door with the key and when i do that the alarm goes off. Help

Lock all the doors from the inside (with all the doors closed), unlock your driver's door by manually lifting the lock, then press it back down after you are out - this will prevent the alarm from sounding when you use the key to unlock the door.
Not finding what you are looking for?

221 views

Ask a Question

Usually answered in minutes!

Top Lincoln Experts

ZJ Limited
ZJ Limited

Level 3 Expert

17989 Answers

Thomas Perkins
Thomas Perkins

Level 3 Expert

15088 Answers

Brad Brown

Level 3 Expert

19187 Answers

Are you a Lincoln Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...