Adui tt roof fuse

A lot of thing's , has sensors , switches , a control module , relay's etc....
The roof opening panel is an electronically operated panel that can be opened or closed by pressing a switch located on the overhead console. It also has one-touch open, one-touch close, one-touch vent open and one-touch vent close features.

Roof Opening Panel The roof opening panel assembly uses an integrated motor and module to operate the roof opening panel. The roof opening panel motor and module are installed new as an assembly. The roof opening panel is an electronically operated glass panel that can be opened, closed or tilted by the roof opening panel switch. Actuating the switch in either a forward or rearward motion supplies a ground to the roof opening panel motor/module. The roof opening panel has one-touch open and one-touch close features that are activated when the switch is momentarily pressed to the double detent OPEN or CLOSE position. These functions are controlled by the roof opening panel motor/module.
The roof opening panel motor must be initialized whenever the roof opening panel motor has been removed from the roof opening panel system, the roof opening panel assembly has been removed from the vehicle, a new roof opening panel motor has been installed or a new roof opening panel assembly has been installed.

Plus the mechnical parts of it .

Visual Inspection Chart Mechanical Electrical

• Roof opening panel
• Roof opening panel frame
• Roof opening panel drain hoses
• Roof opening panel lifter assemblies
• Roof opening panel trough
• Roof opening panel air deflector assembly
• Roof opening panel seal
• Roof opening panel shield

• Battery junction box (BJB) fuse 33 (20A)
• Smart junction box (SJB) fuse 12 (7.5A)
• Circuitry
• Accessory delay relay
• Roof opening panel motor and module assembly
• Roof opening panel switch

The roof opening panel is an electronically operated panel that can be opened or closed by the roof opening panel switch. Actuating the switch in either a forward or rearward motion supplies a ground to the roof opening panel motor. The vent and soft-stop functions are controlled by the roof opening panel motor. These positions are obtained when an internal motor cam opens the roof position switch, removing the ground from the switch. The roof opening panel has an express open feature activated when the switch is pressed momentarily. The roof opening panel is closed by continuous activation of the switch until the sunroof stops movement. This function is controlled by the roof opening panel motor.

Visual Inspection Chart Mechanical Electrical

• Roof opening panel
• Opening shield
• Roof panel frame
• Opening shield guide feet

• Central junction box (CJB) fuses:
  • 2 (20A)
  • 29 (5A)
• Battery junction box (BJB) fuse 1 (60A)
• Accessory delay relay
• Roof opening panel control switch
• Circuitry
• Roof opening panel motor

• The roof opening panel does not open or close

• Central junction box (CJB) fuse:
  • 2 (20A).
  • 29 (5A).
• Battery junction box (BJB) fuse 1 (60A).
• Circuitry.
• Roof opening panel control switch.
• Roof opening panel motor.

• Go To Pinpoint Test E .

Do the power windows and power locks work ?

E6 CHECK VOLTAGE TO THE ROOF OPENING PANEL MOTOR - CIRCUITS 400 (LB/BK) AND 1173 (BN/OG)

• Key in OFF position.
• Disconnect: Roof Opening Panel Motor C920.
• Key in ON position.
• NOTE: Activate accessory delay relay for this check.
• Measure the voltage between roof opening panel motor C920-4, circuit 400 (LB/BK), and ground; and between roof opening panel motor C920-7, circuit 1173 (BN/OG), and ground.
• Are the voltages greater than 10 volts?

Yes
GO to E7 .

No
REPAIR circuit 400 (LB/BK) or circuit 1173 (BN/OG). TEST the system for normal operation. If you can't do electrical testing , there is a manual way to close it .
Roof Opening Panel Manual Operation

1. Remove the overhead console. For additional information, refer to Overhead Console in this section.

1. Insert a hex-head screwdriver in the center of the manual drive slot to depress the release pin. Rotate the screwdriver clockwise until the roof opening panel is closed.

has to be the switch that operates sun roof

Check fuses and wiring. If all is good, I suggest carrying around towels and plastic wrap... Just kidding. If nothing works, take it to O'Reilly and have the computer checked. It could just be a burned motor, which is an entirely different story.

there is no manual method. It sounds like a limit switch is not working. Can you hear the motor try to operate? If you push up on the back of the glass a little bit while hitting the switch, what happens.

go here for villager help

http://groups.yahoo.com/group/villagerquest/


The sliding roof panel system consists of the following components:

• RH circuit breaker
• Timer module
• Power window relay
• Roof sliding panel switch (15B691)
• Roof glass panel (50054)
• Sliding roof panel motor (15790)
• Halo moulding
• Roof sliding panel headlining (519A02)
• Roof sliding panel slide links (502M78)
• Roof sliding panel housing (502C22)
• Roof air deflector (500A26)
• Center green diode strip

-------------------------------------
When the roof sliding panel switch is activated, a gear on the sliding roof panel motor drives a spline on the roof sliding panel housing. Within the roof sliding panel housing, the spline is connected to two sliding roof panel cables which cause the roof sliding panel slide links to slide and the roof glass panel to open or to close. The sliding roof panel cables and the spline are part of the roof sliding panel housing. Neither the sliding roof panel motor nor the roof sliding panel housing can be disassembled. If a malfunction is detected with either of these assemblies, the assembly must be replaced.
----------------------------------------------------------------------------
VISUAL INSPECTION CHART Mechanical Electrical

• Damaged sliding roof panel
• Sliding roof panel height adjustment
• Sliding roof panel fore and aft adjustment

• Blown fuse(s):
  • 30A PWR WDW
• Damaged circuit breaker #1
• Damaged wiring harness
• Loose or corroded connections

------------------------

• Sliding Roof Panel Does Not Open or Close

• Fuses.
• Circuit breaker #2.
• Power window relay.
• Sliding roof panel motor.
• Roof sliding panel switch.
• Circuit.

• GO to Pinpoint Test E1 .

• Sliding Roof Panel Will Not Stop in Vent Position

• Sliding roof panel motor.

Switch Removal

1. Disconnect the battery ground cable (14301).
   

1. Gently pry the overhead console from the headliner.
   

1. Disconnect the sliding roof panel electrical connector from the overhead console.
   

1. Disconnect the rear quarter window switch electrical connector from the overhead console, if equipped.
   

1. Disconnect the map lamp electrical connector from the overhead console.
   

1. Remove the overhead console.
   

1. Remove the two roof sliding panel switch screws and the roof sliding panel switch (15B691).
   

--------------------------------------------------------------------------------
Motor Removal

1. Place the roof glass panel (50054) in the closed position.
   

1. Remove the roof headlining (51916). Refer to Section 01-05 for the removal procedure.
   

1. Remove the two sliding roof panel relays from their brackets.
   
   
   
   
   

1. Disconnect the two sliding roof panel motor electrical connectors.
   

1. Remove the two sliding roof panel motor screws and the sliding roof panel motor (15790
   

The same problem. How can I fix it?

Look in hand book for manual operation of roof.
The handle is located side of dash,insert as shown.
Start manual operation
You do not have to do the full opening/closure
After the operation starts and releases rear flap remove handle,
Start car.Check electric operation of roof
This op should have reset it

I had problem with the flaps staying open,pilot error you have to have the engine running and it's fine wish the dealer told me that. The only problem I have is when the roof has been down for a while , when it's then closed there is a small bump that appears on the near side.

Adrian in Somerset

Section 01-17: Roof Panel, Sliding—Electric 1996 Taurus, Sable Workshop Manual DESCRIPTION AND OPERATION Electric Operation The sliding roof panel (502B98):

• is available as an option.
• is electrically operated through the accessory delay relay (controlled by generic electronic module (GEM)).
• is of self-storing design.
• requires a specific headliner.
• utilizes a unique roof console and dome lamp.
• has an air deflector.

The electrical system operates in the following manner:

• Two switches control movement of the roof panel.
• When the SLIDE roof sliding panel switch (15B691) is rocked rearward, the roof sliding outer glass panel (502A82) slides into the storage space between the roof trim panel (51968) and the roof panel, exposing an opening over the front seats.
• When the SLIDE roof sliding panel switch is rocked forward with the roof sliding outer glass panel fully back in the storage space, the roof sliding outer glass panel moves forward from the storage position.
• The rear portion of the roof sliding outer glass panel moves upward on two lifter arms near the end of the forward travel, allowing a weather-tight seal when the roof sliding outer glass panel is closed.
• An AUTO feature allows the SLIDE roof sliding panel switch to be touched momentarily to cause the roof panel to automatically move to the fully open position.
• When the TILT roof sliding panel switch is rocked forward with the roof sliding outer glass panel fully forward, the rear of the roof sliding outer glass panel pops up to the VENT position.
• With the roof sliding outer glass panel in the VENT position, rocking the TILT roof sliding panel switch rearward closes the roof sliding outer glass panel.

--------------------------------------

• Sliding Roof Panel Does Not Open or Close

• Open power feed fuse.
• Circuitry open/shorted.
• Damaged roof sliding panel switch.
• Damaged sliding roof panel motor.

VISUAL INSPECTION CHART Mechanical Electrical

• Damaged roof panel
• Obstructed roof panel
• Guide
• Damaged drive cable(s)

• Open Power Distribution Box Fuses 1 (40A) or 4 (30A)
• Circuitry open/shorted
• Damaged roof sliding panel switch
• Damaged sliding roof panel motor

Release the hydrolics in the trunk. Then pull the top manually into place.