Abs system enable code c0561 what causes this code

SOURCE: CTS in dash navigation system

There is a company called PAC that specializes in modules like you describe - keeping the steering wheel controls functional with an aftermarket radio.

Click HERE to visit their site. You have to choose a compatible manufacturer. Basically - it is turning the steering wheel controls into a "remote" hidden in the dash.

CLICK HERE for the PAC installation guide for the 2006 CTS

For best results and compatibility, look for a shop in your area that carries PAC - it is a common manufacturer in the BIZ, and have them install it.

The simple answer to your question is YES as long as you use the module compatible for the brand of radio you are installing.

Thanks for using FixYa - a FixYa rating is appreciated for taking the time to answer your FREE question.

SOURCE: what do the trouble codes mean? p0305 and p0135

P0305 IS # 5 CYLINDER MISFIRE DETECTED.P0135 IS BANK 1 SENSOR 1 OXYGEN HEATER CIRCUIT FAILURE

rtpflh

• 546 Answers
• Posted on Sep 30, 2009

SOURCE: The AM/FM radio in my 2003 cadillac CTS faded to only static

check antenna cable connections at radio & antenna.suspect power antenna if equipped.

SOURCE: 2003 cts cadillac need unlock code for radio cd

call cadillac or maybe even gm dealer and give them vin number
gm dealer ask for martin @ 281-929-3250....houston tx

Duane Wong

• 6826 Answers
• Posted on Jul 03, 2010

SOURCE: need trouble codes for 1993 Cadillac F31 F47

Reading Codes OBD-I Systems Fig. 1: Diagnostic trouble codes — 4.5L engine
Fig. 2: Diagnostic trouble codes — 4.9L engine
Fig. 3: Diagnostic trouble codes — 4.6L engine
Listings of the trouble codes for the various engine control systems covered in this manual are located in this section. Remember that a code only points to the faulty circuit NOT necessarily to a faulty component. Loose, damaged or corroded connections may contribute to a fault code on a circuit when the sensor or component is operating properly. Be sure that the components are faulty before replacing them, especially the expensive ones. The Assembly Line Diagnostic Link (ALDL) connector or Data Link Connector (DLC) may be located under the dash and sometimes covered with a plastic cover labeled DIAGNOSTIC CONNECTOR.

1. On all 1990–95 models the diagnostic trouble codes can be read by grounding test terminal B. The terminal is most easily grounded by connecting it to terminal A (internal ECM ground). This is the terminal to the right of terminal B on the top row of the ALDL connector.
2. Once the terminals have been connected, the ignition switch must be moved to the ON position with the engine not running.
3. The Service Engine Soon or Check Engine light should be flashing. If it isn't, turn the ignition OFF and remove the jumper wire. Turn the ignition ON and confirm that light is now on. If it is not, replace the bulb and try again. If the bulb still will not light, or if it does not flash with the test terminal grounded, the system should be diagnosed by an experienced driveability technician. If the light is OK, proceed as follows.
4. The code(s) stored in memory may be read through counting the flashes of the dashboard warning lamp. The dash warning lamp should begin to flash Code 12. The code will display as one flash, a pause and two flashes. Code 12 is not a fault code. It is used as a system acknowledgment or handshake code; its presence indicates that the PCM can communicate as requested. Code 12 is used to begin every diagnostic sequence. Some vehicles also use Code 12 after all diagnostic codes have been sent.
5. After Code 12 has been transmitted 3 times, the fault codes, if any, will each be transmitted 3 times. The codes are stored and transmitted in numeric order from lowest to highest. NOTE: The order of codes in the memory does not indicate the order of occurrence.
   
6. If there are no codes stored, but a driveability or emissions problem is evident, the system should be diagnosed by an experienced driveability technician.
7. If one or more codes are stored, record them. Refer to the applicable Diagnostic Code chart in this section.
8. Switch the ignition OFF when finished with code retrieval or scan tool readings. NOTE: After making repairs, clear the trouble codes and operate the vehicle to see if it will reset, indicating further problems.