20 Most Recent 2005 Jeep Wrangler - Page 4 Questions & Answers

0helpful
1answer

Brake lights wont work

have you checked the fuses and relays. does the the brakes come on when you put on the head lights
11/19/2012 12:04:45 PM • 2005 Jeep... • Answered on Nov 19, 2012
0helpful
2answers

2005 Jeep wrangler w/rough idle and hesitates when you accelerate

try fuel injectors....run a bottle or two with full tank through it and see if that dont solve the problemo.....
10/19/2012 1:03:14 AM • 2005 Jeep... • Answered on Oct 19, 2012
0helpful
1answer

Where is the vacuum line off the exhaust system for the heater

I've never seen a vacuum line go from exhaust to heater, if you are haveing trouble with your heater there are questions that should be asked 1 does the blower motor work when you turn on the fan 2 does the heater core flow fluid (hot coolant) check this by feeling the heater core hoses 1 should be hot and 1 is usually warm or hot. 3 are the climate control switches functioning properly
10/15/2012 11:14:49 PM • 2005 Jeep... • Answered on Oct 15, 2012
0helpful
1answer

What would cause my alternator to stop charging and all my guages to stop working as weel as not enguaging the starter

My first guess would be a blown major fuse, or a problem with the key switch.
9/23/2012 1:42:58 AM • 2005 Jeep... • Answered on Sep 23, 2012
0helpful
3answers

Air conditioner in 2005 jeep wrangler x

Yeah, I would go up hill or pull away from a stop and the A/C would cut out and then come back once my speed was stabilized. It was a vacuum hose leak !! This mostly affected the upper dash blower fan.
8/3/2012 11:54:31 AM • 2005 Jeep... • Answered on Aug 03, 2012
0helpful
1answer

Doesnt want to start after getting warm

HelloThe engine and transmission in this cars drive train are fully electronically controlled by a computer called the PCM (Power Train Control Module). Whenever a problem like this occurs the computer stores a record of the problem (there are of course some exceptions to this, like the fuel pump, engine coolant temperature sensor and MAF sensor for instance) in the form of a fault code in its memory, to read these fault codes you must have the systems memory scanned with a special tool. Once the fault code(s) are read you then must perform the appropriate diagnostic testing to find and resolve the problem(s) DO NOT REPLACE ANY PARTS UNTIL A TRAINED TECHNICAIN HAS DIAGNOSED THE PROBLEM TO AVOID SPEDING YOUR HARD EARNED MONEY ON PARTS THAT MAY NOT CORRECT THE PROBLEM

7/19/2012 9:56:16 PM • 2005 Jeep... • Answered on Jul 19, 2012
0helpful
1answer

05 jeep wrangler wont start,has power to lights radio,battery good starer good.when you try to start inst.cluster does not come up.

check your engine block ground or the battery ground make sure the engine is properly grounded or is still grounded
6/19/2012 4:11:04 PM • 2005 Jeep... • Answered on Jun 19, 2012
0helpful
1answer

Engine code reader

depends on how deep you want to get into auto repair or just to check engine codes. SNAP-ON Versus is state of the art with a price tag of 10,000 dollars. you can get simple hand held readers for about 150 dollars at a local parts store.
5/24/2012 3:00:46 AM • 2005 Jeep... • Answered on May 24, 2012
0helpful
1answer

Obd code: p2058

You will need a scanner that can read live engine running system data to see what is going on in the fuel control system. You can buy this type of scanner on eBay for about $100.00 Look for this "OBD2 Live Data Scanner"
5/18/2012 4:30:14 PM • 2005 Jeep... • Answered on May 18, 2012
0helpful
2answers

Cruise Control problem

control box??? its part of the multifunction switch. not working right?? replace broken parts.
5/12/2012 4:24:21 PM • 2005 Jeep... • Answered on May 12, 2012
0helpful
1answer

Removing the ignition switch

Disable airbag, remove steering wheel, remove - but do not disconnect - electrical switch. In the metal housing near the ignition switch is a small slot. The slot may be closed off with flashing (a thin metal deposit resulting from casting process used to make the housing). Use a #3 flat tip screwdriver, push firmly into the slot and pull out switch.
5/7/2012 2:19:02 PM • 2005 Jeep... • Answered on May 07, 2012
0answers
Not finding what you are looking for?
2005 Jeep Wrangler Logo

342 questions posted

Ask a Question

Usually answered in minutes!

Popular Products

Top Jeep Experts

ZJ Limited
ZJ Limited

Level 3 Expert

17989 Answers

Ronny Bennett Sr.
Ronny Bennett Sr.

Level 3 Expert

6988 Answers

Thomas Perkins
Thomas Perkins

Level 3 Expert

15088 Answers

Are you a Jeep Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

View Most Popular

Wrangler Jeep

  • Wrangler Jeep

Most Popular Question

gear slip when putting into first third

  • Cars & Trucks
Loading...