2009 Dodge Caliber SXT - Answered Questions & Fixed issues

Go to this site

Do the 4 way flashers flash the lights?If they do flash it may be the signal light switch or power to it.

this should help with pics...... https://www.justanswer.com/dodge/4dvh7-hi-guys-2007-caliber-70-000-miles-check-engine-light-o2-sensor.html

Did you check power an the ground . Find a wiring diagram an do a voltage drop test . basic voltage drop testing for automotive electrical testing

http://www.caliberforumz.com/showthread.php/32854-CRD-fuel-filter-replacement this link will show location and how to replace filter

Throttle position sensor is not providing good data. Broken wire or TPS sensor or gas pedal interface out of whack. Take / tow to dealer.

Pull out the cover over the gear switch selector. Then pull out the vent controller and make sure that the wiring connector is connected tightly to the back of the switch.

If you are under the car look up on the back side of the block toward the drivers side near the transmission it is held in place with 1 bolt (use a 10mm socket) and 1 electrical connector super easy to remove/reinstall once under the car

You need to take this in, the seal might have failed because of a bushing wearing out. It is not something that you can do without special tools and equipment.

Question re-written for clarity. Question moved to model category. There aren't any. The headlights are a function of the IPM (integrated power module). Fuse 36 is the control according to this. Headlamp / Washer Control / Smart Glass

What's the 2007 Dodge Caliber headlight relay location?

Vehicle History https://www.vehiclehistory.com > questions > whats-th... Jul 16, 2020 - The head lamps are controlled by a fuse in the engine bay. To locate the integrated power module, open the hood and look on the driver's side of ... 2 answers · Top answer: The 2007 Dodge Caliber is noted for driver's side low beam headlights that f

Dodge Caliber (2006-2012) fuses

Fuse Box Diagrams https://fuse-box.info > dodge > dodge-caliber-2006-2... Fuse box diagram (location and assignment of electrical fuses) for Dodge Caliber (2006, 2007, 2008, 2009, 2010, 2011, 2012).

Fuses and relay Dodge Caliber - Fuse box diagram

fusesdiagram.com https://fusesdiagram.com > dodge > fuses-and-relay-d... Locate fuse and relay. Fuse box diagram. Identifying and legend fuse box Dodge Caliber 2007-2012. ..

The torque specification for the manifold to catalytic converter bolts on a 2007 Dodge Caliber RT with a 2.4L engine is 26 Nm (19 lb-ft). It's important to use a torque wrench to ensure the proper torque is applied to the bolts to avoid over-tightening or under-tightening, which could lead to problems with the exhaust system.

The fuel filter is in the tank connected to the fuel pump most all new auto`s are doing that. Take it to a shop have them change it and by the way go ahead and change the fuel pump at the same time.

More information please. What exactly are you having issues with? Removing the actual flywheel isn't too difficult, it simply bolts to the end of the crankshaft. The hard work is actually getting to it. You need to remove the transmission and bell housing as well as the clutch assembly to get to the bolts holding the flywheel to the crankshaft. The transmission AND the actual flywheel are VERY heavy and I would not recommend doing this as a 'driveway' job. *NOTE* - The mount holes on a flywheel and the crankshaft end are NOT evenly spaced. All six holes will only line up in one exact position. This is a marker setup to keep the system correctly balanced. - Make sure the mount bolts are tightened to the correct torque setting! One loose bolt can cause a world of problems.

get a repair/service manual it will show tools-equipment needed as well as checking out if your capable of doing the removal https://www.youtube.com/watch?v=JXQgIu9IzTw this shows basic removal at a boneyard and the use of equipment there to remove it also not shown is the removal of all the components and sensors needed to get to bolts

https://www.modifiedlife.com/2011-dodge-caliber-car-radio-wiring-guide/

My car got hit yesterday in the back on the rear right side of my 2008 Dodge Caliber is it worth fixing

sounds like possible broken internal electrical trace connection. buy new stereo at BestBuy/Frys/etc and have them install it

On this website you find fuse box diagram and description for Dodge Caliber (2008) https://www.carknowledge.info/dodge-caliber-2008-fuse-box-diagram/ https://www.autogenius.info/dodge-caliber-2008-fuse-box-diagram/

Most oil sender units are a near the oil filter.

Do you have a user manual? this is where you find that info. We can help you locate the manual if need good luck https://www.6ya.com/mrmmike