2009 Dodge Caliber 2.4 - Answered Questions & Fixed issues

Question re-written for clarity. Question moved to model category. There aren't any. The headlights are a function of the IPM (integrated power module). Fuse 36 is the control according to this. Headlamp / Washer Control / Smart Glass

What's the 2007 Dodge Caliber headlight relay location?

Vehicle History https://www.vehiclehistory.com > questions > whats-th... Jul 16, 2020 - The head lamps are controlled by a fuse in the engine bay. To locate the integrated power module, open the hood and look on the driver's side of ... 2 answers · Top answer: The 2007 Dodge Caliber is noted for driver's side low beam headlights that f

Dodge Caliber (2006-2012) fuses

Fuse Box Diagrams https://fuse-box.info > dodge > dodge-caliber-2006-2... Fuse box diagram (location and assignment of electrical fuses) for Dodge Caliber (2006, 2007, 2008, 2009, 2010, 2011, 2012).

Fuses and relay Dodge Caliber - Fuse box diagram

fusesdiagram.com https://fusesdiagram.com > dodge > fuses-and-relay-d... Locate fuse and relay. Fuse box diagram. Identifying and legend fuse box Dodge Caliber 2007-2012. ..

The torque specification for the manifold to catalytic converter bolts on a 2007 Dodge Caliber RT with a 2.4L engine is 26 Nm (19 lb-ft). It's important to use a torque wrench to ensure the proper torque is applied to the bolts to avoid over-tightening or under-tightening, which could lead to problems with the exhaust system.

The fuel filter is in the tank connected to the fuel pump most all new auto`s are doing that. Take it to a shop have them change it and by the way go ahead and change the fuel pump at the same time.

More information please. What exactly are you having issues with? Removing the actual flywheel isn't too difficult, it simply bolts to the end of the crankshaft. The hard work is actually getting to it. You need to remove the transmission and bell housing as well as the clutch assembly to get to the bolts holding the flywheel to the crankshaft. The transmission AND the actual flywheel are VERY heavy and I would not recommend doing this as a 'driveway' job. *NOTE* - The mount holes on a flywheel and the crankshaft end are NOT evenly spaced. All six holes will only line up in one exact position. This is a marker setup to keep the system correctly balanced. - Make sure the mount bolts are tightened to the correct torque setting! One loose bolt can cause a world of problems.

get a repair/service manual it will show tools-equipment needed as well as checking out if your capable of doing the removal https://www.youtube.com/watch?v=JXQgIu9IzTw this shows basic removal at a boneyard and the use of equipment there to remove it also not shown is the removal of all the components and sensors needed to get to bolts

https://www.modifiedlife.com/2011-dodge-caliber-car-radio-wiring-guide/

My car got hit yesterday in the back on the rear right side of my 2008 Dodge Caliber is it worth fixing

sounds like possible broken internal electrical trace connection. buy new stereo at BestBuy/Frys/etc and have them install it

On this website you find fuse box diagram and description for Dodge Caliber (2008) https://www.carknowledge.info/dodge-caliber-2008-fuse-box-diagram/ https://www.autogenius.info/dodge-caliber-2008-fuse-box-diagram/

Most oil sender units are a near the oil filter.

Do you have a user manual? this is where you find that info. We can help you locate the manual if need good luck https://www.6ya.com/mrmmike

Might be clockspring in steering wheel

your blender door is not closing , check accuator

The best solution you'll get from books at www.reliable-store.com These are books containing info on repair, service, troubleshooting, parts info, assembling dissemble, removal, error/fault codes, wiring diagrams and everything on any vehicles cars, atv, trucks. forklifts, boats, excavators etc

If I remember right, Standard Caliber horn is on the drivers side behind bumper fascia. Not an easy retrieval but can be done. I hope this helps you on your fishing quest for that horn :o) Jesus loves you, John 3:16-17 (KJV)

Which speed sensor? I encountered a Nissan with at least three. Speedo. Transmission. and Engine computer. Seems strange but the easiest way to look this up is the company that makes add on cruise controls. They are experts in speed sensors across many brands and models. http://www.rostra.com/

I tried the DIY service and repair manuals from a website and it actually helped me repair transmission problem in my jcb 3cx site-master. it wont move forward or reverse, engine is good both solenoids for forward and reverse work. I don't have much technical knowledge but I just followed it step-wise, and works perfect! got it from www.reliable-store.com

There's this website www.reliable-store.com They have books on ALL vehicles. it covers wiring diagrams, electrical diagrams, fuse diagram, torque specs, PCV, error codes, fault codes, service info, repair info, parts info, owner's/service/repair/parts/maintenance manuals etc everything totally.. I have 1987 toyota 4runner model and I keep servicing and when needed repair it on my own. worth it !!!

I think you could use this manual method instead.. My nephew used it to repair my car and it's perfectly fine now. Here's the website he bought it from. www.reliable-store.com

If you're comfy with manuals then i know few websites that can help you with it. Bcause I've bought it from various websites so I know how each site deals. try www.reliable-store com . Very helpful