2007 Dodge Caliber 1.8 - Answered Questions & Fixed issues

Some fixya user told me a w ebsite reliable-store it is very good.. I used it to repair my shredder it had some spark issue which wasn't easily fixed. you can go there and try

check for clutch fluid leak or broken clutch cable if yours is cable operated

Check fuse for fuel pump then check fuel pump relay if they are good then most likely it's the fuel pump the fuel pump is in the tank and it's called a fuel modules very expensi

18.3 ft/lbs or 220 In/lbs.

ignition coil dead ? battery earth cable came loose ?

what fuel is it.

I would work on the cause and cure of overheating problem first. Over heating would cause transmission to run hot as well being how fluid is cooled through radiator.

Check your fuse diagram on the fuse box lid under the hood

Question re-written for clarity. Question moved to model category. There aren't any. The headlights are a function of the IPM (integrated power module). Fuse 36 is the control according to this. Headlamp / Washer Control / Smart Glass

What's the 2007 Dodge Caliber headlight relay location?

Vehicle History https://www.vehiclehistory.com > questions > whats-th... Jul 16, 2020 - The head lamps are controlled by a fuse in the engine bay. To locate the integrated power module, open the hood and look on the driver's side of ... 2 answers · Top answer: The 2007 Dodge Caliber is noted for driver's side low beam headlights that f

Dodge Caliber (2006-2012) fuses

Fuse Box Diagrams https://fuse-box.info > dodge > dodge-caliber-2006-2... Fuse box diagram (location and assignment of electrical fuses) for Dodge Caliber (2006, 2007, 2008, 2009, 2010, 2011, 2012).

Fuses and relay Dodge Caliber - Fuse box diagram

fusesdiagram.com https://fusesdiagram.com > dodge > fuses-and-relay-d... Locate fuse and relay. Fuse box diagram. Identifying and legend fuse box Dodge Caliber 2007-2012. ..

The torque specification for the manifold to catalytic converter bolts on a 2007 Dodge Caliber RT with a 2.4L engine is 26 Nm (19 lb-ft). It's important to use a torque wrench to ensure the proper torque is applied to the bolts to avoid over-tightening or under-tightening, which could lead to problems with the exhaust system.

The fuel filter is in the tank connected to the fuel pump most all new auto`s are doing that. Take it to a shop have them change it and by the way go ahead and change the fuel pump at the same time.

More information please. What exactly are you having issues with? Removing the actual flywheel isn't too difficult, it simply bolts to the end of the crankshaft. The hard work is actually getting to it. You need to remove the transmission and bell housing as well as the clutch assembly to get to the bolts holding the flywheel to the crankshaft. The transmission AND the actual flywheel are VERY heavy and I would not recommend doing this as a 'driveway' job. *NOTE* - The mount holes on a flywheel and the crankshaft end are NOT evenly spaced. All six holes will only line up in one exact position. This is a marker setup to keep the system correctly balanced. - Make sure the mount bolts are tightened to the correct torque setting! One loose bolt can cause a world of problems.

get a repair/service manual it will show tools-equipment needed as well as checking out if your capable of doing the removal https://www.youtube.com/watch?v=JXQgIu9IzTw this shows basic removal at a boneyard and the use of equipment there to remove it also not shown is the removal of all the components and sensors needed to get to bolts

https://www.modifiedlife.com/2011-dodge-caliber-car-radio-wiring-guide/

My car got hit yesterday in the back on the rear right side of my 2008 Dodge Caliber is it worth fixing

sounds like possible broken internal electrical trace connection. buy new stereo at BestBuy/Frys/etc and have them install it

On this website you find fuse box diagram and description for Dodge Caliber (2008) https://www.carknowledge.info/dodge-caliber-2008-fuse-box-diagram/ https://www.autogenius.info/dodge-caliber-2008-fuse-box-diagram/

Most oil sender units are a near the oil filter.

Do you have a user manual? this is where you find that info. We can help you locate the manual if need good luck https://www.6ya.com/mrmmike

Might be clockspring in steering wheel