20 Most Recent 2011 Toyota RAV4 Questions & Answers

If I remember right that has to have a source of vacumn from the engine. Check any hoses (small about the size of dime coming out of the firewall to the engine it sounds like it came loose also is your vehicle idle higher or miss anytime now? we will get you going just work with me

You recently changed the engine air filter and now, the Check Engine light is on and the LS D light flashing. When you opened the filter housing, you inadvertently disconnected a small hose that is connected to the housing. (See photo) This will result in the lights mentioned coming on. Simply reconnect the hose (it can be simply pushed in) and the engine will perform normally. The Check Engine light will still be on though. The error code will need to be cleared using a dongle that connects to the OBD ll connector under the driver side dashboard and an a smartphone app that connects to the dongle through Bluetooth.

The function of the trac is only to avoid sliding on slippery ground, but in normal conditions it does not affect anything

Visit the on-line store, know as reliable-store, they have the repair manuals. I'm sure you will get the solution of your problem. Best Manuals

That passenger doors actuator could be the problem or the door switch

That is battery/battery terminal/corrosion problem. Please clean the terminals really good, and not on the outside, on the inside. The metal (lead) of the battery terminal and the band (copper) of the terminal need to be shiny bright on the inside. These need to be cleaned periodically, like about every 6 months or a year. Also, take you car to a honest shop and have your battery tested. God bless your efforts.

yes you must remove the crossbar, i had to do it with my monte carlo multiple times

Yes should be in engine compartment but check owners manual

It is how it must work. Nothing wrong with your vehicle. However, when you switch the car completely off and remove the key, the oil and engine lights must be off.

Sounds like the stereo is still on I phone mode,is there a source button ?Should be able to scroll through to radio mode with that button,what brand stereo,does it have a cd player? does that work ?

Warped front rotors,replace or machine flat if they aren't worn below spec.Most parts shops can give you the specs for the rotors.

code p0171 refers top system too lean, bank 1===causes---intake/exhaust leak--air system---MAF/VAF sensor--fuel pressure/pump--injector/s ----HO2S

No...just in this order door handle screws first.use a flat head screw driver between the metal door and door card and just twist the screwdriver until you hear it pop.tackle the sides and bottom before the top.the top should free itself when you slide the whole door card upwards.when refitting slide the top into position before pressing home the studs on the side and bottom.i usually just use the edge of my fist to tap them home.

MIRROR , no reason given? , but yes, yes if you cant see screws that means they are inside door. yes, the FSM COVERS ALL THAT,READ IT http://www.helminc.com/helm/search_service_owner.asp?Style=helm&class_2=TOY

in most cases, you see no screws there but there are, and are INSIDe, (can only be 2 places) so.... yes.

The trim may have several plugs that hide bolts/screws. Look for those and remove with care using a nail remover or flat object like a putty knife. after removing any screws, the trim may come off or have to be pried off. Some overlaps overs and it is better to remove the ones that are on top first. The rubber trim along the edge is usually pliable and with give. Make sure to remove seatbelts and the like if attached to the same trim. Door trim may not have sufficient space to hold wires but they may have to be moved to access under the carpet or channels where the wires may be run. Be sure to remember the order of removal and retain all fasteners. Be very careful to put it all beck correctly and not to smash or snag any wires. Take special care when running through holes in frame not to allow it to contact sharp edges. Tape over or cover edges where needed. For your problem, look for clips around edges that may have to be released.

Yes, The panel needs to be removed. Here is a video of the )^ but your car is almost identical. 2006 rav4 mirror replacement

yes