Kia Cars & Trucks - Page 3 - Recent Questions, Troubleshooting & Support
2004 kia sorento 4 wheel wont engage
check all fuses and relays does the light on the dash come on and is the switch ok or unplugged as well you have a electric motor on the transfer case if its unplugged or burnt it wont engage it looks like a wiper motor at the end of the transmission
Were is the map sensor located at on a 2002 kia spectra
I've checked both of my repair manuals for this vehicle. One is Chiltons, the other is Haynes. They both discuss a Mass Airflow Sensor, but no mention of a MAP. I then checked the book covering my GMC S-15 and found the MAP, but no MAF sensor.
Since the location is different, depending on engine size, my best advice is for you to obtain the same repair manual. It has pictures and leads you step-by-step through the replacement procedure. These books also list the diagnostic codes and what they mean.
2004 Kia Spectra 2.0. What is the spark plug gap please?
Question edited for clarity.
Question moved to model category.
It depends on the plug that you use. Some are Pre-Gapped.
Spark plug gap - Kia Forum
kia-forums.com
https://www.kia-forums.com > threads > spark-plug-gap
Aug 9, 2019 - I'm installing new NGK spark plugs on a 07 Spectra. There is no-where in the manual that show the correct gap. They told me at Auto-Zone the gap is .044...
Spark plug gap ' Kia Forum
Aug 1, 2019
Is this the proper spark plug gap? - Kia Forum
Aug 1, 2019
Spark Plug Torque/Gap - Kia Forum
Nov 16, 2014
Spark Plug Gap ' Kia Forum
Aug 1, 2019
More results from www.kia-forums.com
2004 KIA SPECTRA 1.8L L4 Spark Plug
RockAuto
https://www.rockauto.com > catalog > kia,2004,spectra,1...
GM Original Equipment; Conventional; Pre-Set Gap: 0.041" ($0.50 Rebate Available!).
2004 KIA SPECTRA 2.0L L4 Spark Plug
RockAuto
https://www.rockauto.com > catalog > kia,2004,spectra,2...
Original Center Electrode Material is Copper/Nickel; Do Not Gap, Gap is Preset. OE Fine Wire Platinum; Pre-Set Gap: 0.031". Alternate.
1999 kia sephia slugish on takeoff wont shift to high gear
Here are some possible reasons why your car is sluggish on takeoff and won't shift to high gear:
Low transmission fluid: If the fluid level is low, the transmission may not be able to engage properly. Check the fluid level and add more if necessary .
Worn-out oil seal: A worn-out oil seal can cause a fluid leak, which can prevent the transmission from shifting into high gear .
Faulty shift cable or shifter assembly: If the shift cable or shifter assembly is damaged or worn out, it can cause problems with shifting .
Clogged transmission filter: A clogged filter can restrict the flow of fluid and cause shifting problems .
It's recommended that you take your car to a mechanic for a proper diagnosis and repair. They can run an OBD scan to determine the exact issue and provide a solution.
2013 kia soul driver back door window stuck down
A user suggested checking the button for the window lock, which when pushed, only allows the driver's window to work .
If you're still experiencing issues with your window, you may want to try some of these solutions:
Turn your car on and try pulling the window up with a firm grip .
Slamming your car door can help realign your glass window with the tracks .
Remove the door panel and lift the window manually .
If none of these solutions work, it may be time to get a new power window motor .
I think they refer to the device as an actuator.
0/2000
Does anyone know how to fit a clutch kit for a Kia sorento 2014
If you are not sure about changing a clutch pay a good mechanic to do it for you. This isn't really a job you can do easily on your drive or on the street outside your home. Even when you know what your doing it's at least a full day, possibly 2, to do the job. Remember engines and transmissions are VERY heavy and VERY expensive to replace if they get dropped or damaged.
To change the clutch with the engine and transmission still in the car is a huge amount of work. You have to support the weight of the engine and transmission separately so you can lower it far enough to separate the transmission from the engine. You will then need to unbolt the old clutch parts on the flywheel.
Then you fit the new clutch kit making sure the friction plate is centred correctly, then refit the transmission to the engine. And finally remount the whole thing back onto the engine mounts.
Not finding what you are looking for?