Jeep Grand Cherokee - Recent Questions, Troubleshooting & Support - Page 2

Question edited for clarity. Question moved to model category.

P0507 - Meaning, Causes, Symptoms, & Fixes - FIXD app

fixdapp.com https://www.fixdapp.com > blog > p0507-code Mar 3, 2022 - P0507 can be caused by anything from an intake or vacuum leak to a dirty throttle body to a faulty electric throttle control actuator. It's ... ‎What Does Code P0507 Mean? · ‎How Do I Fix Code P0507?

alot of times when the monitors dont set its because you may have a defective coolant temp sensor or air temp sensor. Some monitors will not run if the sensors never get between 10 degrees of each other and both being under 160 degrees.
The way to check is to use a data scanner. After sitting overnight they should both be about the same temp. Or if you have a data scanner you can force the temp by heating or iceing them to get the desired results before starting the vehicle.
If you dont look at the data before you start the car you will never know if thier faulty

unfortunetly there isnt a owners manual online that is free. I have just searched countless database that would have such. Im sure thats not what you want to hear. But sometimes the correct answer isnt the most favorable. I can provide you with a repair manual for 84-93 xj series cherokee's. But if there is something you want specifically to know about the 93 jeep cherokee you can let me know and i am confident i could help assist you. thanks, MIDWEst-Tek

For strangeness like that you need an auto electrician. The scan tool computer can tell which controller is faulty. https://www.google.com/search?q=auto+electrician+near+me You have a unique issue and that is unusual. https://www.google.com/search?q=2005+Jeep+Grand+Cherokee+Limited+5.7.+No+electrical+power+to+rear+of+vehicle ....

Does the vehicle crank for extended period of time upon first starting? If so the fuel pump needs replacing.

Question edited for spelling of the model names. Question moved to model category. Are you in Limp Mode? Is the Check Engine Light on? Some ideas here including pulling fuses. You probably need an auto electrician though. https://www.google.com/search?q=2013+Jeep+Grand+Cherokee+Laredo+won%27t+shift+out+of+1st+gear ..

Question edited to toss in some CAPS.

Question moved to model category.

Jeep Grand Cherokee (WK; 2005-2010) fuses and relays

https://fuse-box.info > jeep > jeep-grand-cherokee-wk-... Here you will find fuse box diagrams of Jeep Grand Cherokee 2005, 2006, 2007, 2008, 2009 and 2010, get information about the location of the fuse panels ...

2008 Jeep Grand Cherokee fuse box diagram - StartMyCar

https://www.startmycar.com > ... > Fuse box The 2008 Jeep Grand Cherokee has 3 different fuse boxes: ... Jeep Grand Cherokee fuse box diagrams change across years, pick the right year of your vehicle:.

2005-2010 Jeep Grand Cherokee WK Fuse Box Diagram

https://knigaproavto.ru > ... > Jeep > Grand Cherokee Oct 7, 2019 - Fuse Box Layout Jeep Grand Cherokee; engine: 3.0L Deisel, 3.7L, 4.7L, 5.7L and 6.1L (WK; 2004, 2005, 2006, 2007, 2008, 2009, 2010)

• Grand Cherokee » Fuse Diagram

  https://knigaproavto.ru > Fuse Box Diagram > Jeep Fuse Box Layout Jeep Grand Cherokee; engine: 3.0L Diesel, 3.7L, 4.7L, 5.7L and 6.1L (WK; 2004, 2005, 2006, 2007, 2008, 2009, 2010)

ditto and say first if stater works at all cranking word. and if not cranking do so in NEUTRAL when park ever fails. wild guess car is not cranking and step 2 is for most is jumper cable to 2nd car jump starts. the starter can jumper wired cranked too key off to simply test the starter I just saved you $100 and skinned up knuckles. fuses good too. yes I have the shop manual on jeeps i own same jeep is 2010 and is same. there are 6 causes, just 2 tests gets you to 4 causes. ask how. back later.

Hi,You can get new keys from any Jeep dealership.You'll need your ownership and the VIN number (vehicle identification number) That number is located under the windshield on the drivers side bottom corrner.Your best bet is call first to check if anyother information is needed.Good luck hope this has helped,if so please don't forget to rate me......

check thermostat

Sounds familiar - I pulled the rubber boot back and found the black wire was broken. I stripped the wires and put on a couple bullet connectors (terminators) and all is good. Just wish I would have seen this post before I took the door panel off... Oh well...

car runs and drives okay>? no errors in the dash IP cluster? is this car in canada with DRL lamps" Daylight running lamps? not told at al what it does wrong both highs and lows dead, and high flash mode fail? what I do is just look at the fuse to see if they are blown the lid to the fuse box is marked each one named. i will read the USA OEM service manual answer to you. 2005 is same car as my 2010 usa wk model the module front control drives (uses DRIVER) to run all 4 Headlamps. so there is no fuse for lows or highs or left and right. are your lamps factory OEM stock or hacked>? if you scan the PCM OBD2 port there are P16xx codes DTC to see. there is no relay, yes for park and yes for fog sorry none, there. but I am only talking USA non DRL car. why not say what is wrong or problem or a job to do or lamps dead. or wanting to hack in LED or HID lamps all you posted is a hunt to nothing. if is DRL auto lamps the auto controller does use F10 fuse. just a question if lamps fail? do they fail key off key on or key running or all those and all 4 lamps fail?

Bad bendix, replace starter soon or may damage flywheel

Might just be that the pesky ecu needs to be rebuilt. They were known to be failure prone.

No obd 2 since it's a pre 1996 vehicle, so its obd 1. Start turning that key on-off-on-off-on, to get ck engine light to flash out codes.

Rear main seal of engine is leaking. Tough to change....have to drop tranny and remove the flywheel, to get to it.

vehicle rekeyed are keys ign only if so have door slimmed for entry their is no bypass no hotwire have keys cut by vin for vehicle door and order fobs also

you need a locksmith tools and course

no it cant and picking the cylinder probable damaged to where you will now need to replace and programm the system instead of having key[s] made by dealer or an auto approved locksmith using vehicle vin

here it is https://eautorepair.net/Marketing/Default.asp