Jeep Grand Cherokee - Recent Questions, Troubleshooting & Support


bank 2 sensor 1 is passanger side and first sensor on the exhaust. i dont know exactly where it is but from the exhaust manifold follow it down until there is a sensor drilled into your exhaust that is your oxygen sensor. then you go rent a tool specially made just for pulling that part out. Or you can take a wrench and try to pull it first but make sure your engine is warm so it is easier to remove. Once the exhaust cools it is so much harder to remove. If you cant get it with the wrench make sure to rent the tool from like autozone. sometimes there easy sometimes a little difficult. good luck also if it comes out easy id say its about a 5-7 minute job.

2004 Jeep Grand... | Answered 4 hours ago


if it is not a safety recall probably not....jeep quality

Jeep Grand... | Answered 11 hours ago


have the OBD read, sounds like problem with the chassis/suspension/drive train, OBD should give code for the fault

2009 Jeep Grand... | Answered Yesterday


crank sensor would be first guess. second would be bad pcm. try this. start it and whiles its idling wiggle the 3 connectors at the pcm..does it die? theres your problem. if not replace the crank sensor

1999 Jeep Grand... | Answered 2 days ago


check behind rear bumper driver's side

2015 Jeep Grand... | Answered 2 days ago


If it has no bleed screw then you need to loosen the flange nut(that holds the pipe to the slave cylinder). Pump the pedal a couple times then hold it down. Loosen the nut till the fluid comes out. Fasten again. Pump and hold. Loosen etc.

1996 Jeep Grand... | Answered 3 days ago


website https://big-manuals.com/products/copy-of-jeep-grand-cherokee-xj-yj-1995-workshop-service-manual

and this book helped me repair it within an hour, all by myself!!!! It's amazing, no hassle at all
From wiring diagrams, schematic illustrations, spark plugs info, parts info, stepwise instructions, torque specs, error/fault codes, engine info, to every single minute parts, you get everythingg in there you can't imagine how detailed it is

2004 Jeep Grand... | Answered on Jan 07, 2019


even tho lights come on your battery may be to low to start just the other day i had same issue a person car would not start lights would come on i jump started the car and went got a new battery

Jeep Grand... | Answered on Jan 04, 2019


I'm having a problem with my tranny not wanting to shift automatically at all. Seems like a dead stop its stuck in low gear. Have to manually shift and does not go into overdrive. I have a 1993 Jeep Grand Cherokee. Can anyone help me cause I've swiched out throttle control sensor, filter change, new tranny cooler and heavy duty lines. I'm at a loss and scratching my head. Any advice would be greatly appreciated

1994 Jeep Grand... | Answered on Dec 31, 2018


If you take the tail light assembly off and take the bulb out, you'll see three metal contacts on the tail light assembly.  Pry them up slightly and slide a small, folded piece of aluminum foil underneath it.  
Replace the bulb and try to reproduce the problem.  I found this fix online and did it to both sides of my car.. no problems since

2000 Jeep Grand... | Answered on Dec 31, 2018


sounds like the door ajar switch is defective.

1995 Jeep Grand... | Answered on Dec 29, 2018

Not finding what you are looking for?

-12,828 questions posted

Ask a Question

Usually answered in minutes!

Popular Products

Top Jeep Experts

Marvin
Marvin

Level 3 Expert

83843 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22413 Answers

Jeffrey Turcotte
Jeffrey Turcotte

Level 3 Expert

8841 Answers

Are you a Jeep Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

View Most Popular

Jeep Cars & Trucks

  • Forum

View Most Popular

  • Jeep Cars & Trucks
Loading...