Chevrolet Cars & Trucks - Answered Questions & Fixed Issues
Hi how to set a timing belt tensioner pulley when replacing 2011 Chevrolet aveo
Tensioner pulleys are designed to be 'Self Adjusting'. These pulleys are on spring loaded arms so they automatically push against the belt keeping it tight. You use a socket or a spanner to swing the pulley arm back against this spring.
*Note* This is a powerful spring so BE CAREFUL when your working on it!
A lot of these tensioners have two small holes to help with installing a belt. When you swing the tensioner arm back these two holes line up with each other. You can then slide a hex key, or something similar, through both holes and it holds the arm back giving you space to get the belt on.
*Caution* When your ready to release the tensioner DO NOT just pull the hex key out!! With the socket or spanner you used to swing the tensioner arm back push the arm against the spring again, carefully pull the allen key out then Carefully release the pressure on the spring so the pulley sits correctly and tensions the belt.
1999 Chevy Silverado 2500 6.0. Ignition coil ground for it please.
Our Automotive Technician Jeff provides a great answer and lists all the grounds
.
- Jeff Armer Apr 11, 2024Rear wheel drive or 4X4 ?
-
Jeff Armer Apr 11, 2024
G100
On the left radiator support bracket
Power and Grounding Component Views
--
G102
On the right front of the engine block (4.3L)
--
G102
On the left front of the engine block (4.8L, 5.3L, 6.0L)
Power and Grounding Component Views
--
G103
On the right rear of the engine block
Power and Grounding Component Views
--
G104
On the left rear of the engine block
Power and Grounding Component Views
--
G105
On the right front of the engine block (4.3L)
Power and Grounding Component Views
--
G105
On the left front of the engine block (4.8L, 5.3L, 6.0L)
--
G106
On the right front of the engine block (4.3L)
--
G106
On the right rear of the engine block (4.8L, 5.3L, 6.0L)
--
--
G107
Engine to body (engine ground strap)
Power and Grounding Component Views
--
G108
Hood to body (body ground strap)
--
G110
On the left front body mount
Power and Grounding Component Views
--
G200
On the right upper IP at the A pillar
Power and Grounding Component Views
--
G203
On the left upper IP at the A pillar
Power and Grounding Component Views
--
G302
On the left body mount
Power and Grounding Component Views
--
G304
Under the driver seat
Power and Grounding Component Views
--
G305
Inside the passenger compartment on the left side at the B pillar
--
G306
Inside the passenger compartment on the right side at the B pillar
Power and Grounding Component Views
--
G401
On the spare tire hoist bracket
--
G403
On the left frame rail near the body mount
Everytime I hit a bump the rear end slams into the
If this vehicle is equipped with rear struts....not shock absorbers...which most vehicles are equipped with today the sound you are speaking of seems to indicate worn strut plates and bushings... most repair facilities over look these items when replacing the strut housings and thus customer gets this noise even louder now that the struts are new and the plates and bushings are old not able to absorb the shock the vehicles suspension incurrs whuile riding over a bumpy terrain.
2003 Chevrolet Monte Carlo. Is there a reset for the security in my car?
Question edited for clarity and add maker.
Question moved to model category.
LoVe ThE Script kiddie way you spelled your NaMe TiNa. I haven't seen that since the 1990s :>D
Yes there is. Did you disconnect the battery?
- Turn ON the ignition, with the engine OFF.
- Attempt to start the engine, then release the key to ON (vehicle will not start).
- Observe the SECURITY telltale, after approximately 10 minutes the telltale will turn OFF.
- Turn OFF the ignition, and wait 5 seconds .
More items...
•
Dec 17, 2012
Monte Carlo Security Reset: Passlock Procedure ' JustAnswer
JustAnswer
https://www.justanswer.com > Chevrolet Repair
How do you reset the Pass lock System
Monte Carlo Forum
https://montecarloforum.com > monte-carlo-repair-help-8
Feb 5, 2010 - GM says to place in park, shut off the ignition and get out of car, locking it as to depart then unlock and get in, insert key, turn to ACC and ...
Guide: Security Re-Learn Procedure - Monte Carlo Forum
Mar 24, 2008
Car won't start, flashing security light - Monte Carlo Forum
Oct 21, 2011
PassLock Reset procedure 2000 Monte Carlo
Feb 18, 2017
03 SS HELP...it's possessed - Monte Carlo Enthusiast Forums
Nov 12, 2012
More results from montecarloforum.com
There are videos as well
https://www.google.com/search?q=2003+Chevrolet+Monte+Carlo+reset+the+security
..
Not finding what you are looking for?